| About |
|---|
| Monprene OM-10165 is a specialty thermoplastic elastomer, available in NAT, BLK, and colors, designed for overmolding applications like grips and anti-skid parts for a variety of consumer and industrial products. Monprene OM-10165 is a medium hardness, low density opaque grade that exhibits excellent adhesion to nylon.&& |
| Product Description | |
|---|---|
| Supplier | Teknor Apex |
| Generic | TPE |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Excellent Processability,Good flexibility,Smoothness,Good bond,Chemical coupling,Low density,Moderate liquidity,Good wear resistance,Solvent resistance,Soft,Good coloring,Agglomerability |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.918 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 8.0 | g/10min | ASTM D1238 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ASTM D412 | ||
| TD, 100% strain | 2.32 | MPa | ASTM D412 |
| MD, 100% strain | 3.04 | MPa | ASTM D412 |
| tensile strength | ASTM D412 | ||
| TD, 300% strain | 3.67 | MPa | ASTM D412 |
| MD, 300% strain | 4.81 | MPa | ASTM D412 |
| tensile strength | ASTM D412 | ||
| fracture | 5.32 | MPa | ASTM D412 |
| MD, fracture | 5.50 | MPa | ASTM D412 |
| Tensile strain | ASTM D412 | ||
| fracture | 520 | % | ASTM D412 |
| Flow rate, fracture | 440 | % | ASTM D412 |
| tear strength | ASTM D624 | ||
| TD | 29.2 | kN/m | ASTM D624 |
| MD | 30.6 | kN/m | ASTM D624 |
| Compression deformation | |||
| 23℃，22 hr | 29 | % | ASTM D395B |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ASTM D2240 | ||
| Shore A, 1 second, injection molding | 67 | ASTM D2240 | |
| Shore A, 5 seconds, injection molding | 65 | ASTM D2240 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Adhesion to Nylon |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Barrel rear temperature | 204 to 232 | °C | |
| Barrel middle temperature | 227 to 249 | °C | |
| Barrel front temperature | 249 to 266 | °C | |
| Nozzle temperature | 266 to 277 | °C | |
| Processing (melt) temperature | 266 to 277 | °C | |
| Mold temperature | 24 to 60 | °C | |
| Injection pressure | 1.38 to 6.89 | MPa | |
| Injection speed | Fast | ||
| Back pressure | 0.172 to 0.862 | MPa | |
| Screw speed | 50 to 120 | rpm | |
| Cushion | 3.81 to 25.4 | mm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C, 20 in/min |
| 3. Type 1 |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |