| About |
|---|
| apilon 52® DE 55 is a Thermoplastic Polyurethane Elastomer (Polyester) (TPU-Polyester) product. It can be processed by extrusion or injection molding and is available in Europe. Applications of apilon 52® DE 55 include engineering/industrial parts, appliances, coating applications, consumer goods and electrical/electronic applications. Characteristics include: Eco-Friendly/Green Low Temperature Resistant UV Resistant&& |
| Product Description | |
|---|---|
| Generic | TPU-酯 |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Renewable resources,Hydrolysis stability,Antifreeze,Good wear resistance,Grease resistance |
| Availabilitys | Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.22 | g/cm³ | ASTM D792 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tear strength | 145 | kN/m | ASTM D624 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| -20℃ | 无断裂 | ASTM D256 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore D, 3 seconds | 53 | ASTM D2240 | |
| tensile strength | ASTM D638 | ||
| — | 48.0 | MPa | ASTM D638 |
| 100% strain | 13.0 | MPa | ASTM D638 |
| 300% strain | 23.0 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 500 | % | ASTM D638 |
| Bending modulus | |||
| 23℃ | 120 | MPa | ASTM D790 |
| abrasion resistance | 30.0 | mm³ | DIN 53516 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 80 to 100 | °C | |
| Drying time | 2.0 | hr | |
| Recommended maximum moisture content | 0.070 | % | |
| Barrel rear temperature | 180 to 190 | °C | |
| Barrel middle temperature | 185 to 200 | °C | |
| Barrel front temperature | 190 to 215 | °C | |
| Nozzle temperature | 200 to 230 | °C | |
| Mold temperature | 30 to 60 | °C | |
| Injection pressure | 50.0 to 100 | MPa | |
| Recommended maximum moisture content | 0.070 | % | |
| Barrel 1 zone temperature | 160 to 185 | °C | |
| Barrel 2 zone temperature | 170 to 200 | °C | |
| Barrel 3 zone temperature | 175 to 210 | °C | |
| Barrel 4 zone temperature | 180 to 220 | °C | |
| Nozzle temperature | 170 to 210 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. With Notch |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |