| About |
|---|
| Miramid® FB30C is a Polyamide 6 (Nylon 6) material filled with 30% glass bead. It is available in Europe for injection molding. Important attributes of Miramid® FB30C are: Chemical Resistant Crystalline Good Aesthetics Good Dimensional Stability Good Stiffness Typical applications include: Engineering/Industrial Parts Housings&& |
| Product Description | |
|---|---|
| Supplier | BASF |
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Low warping,Good surface appearance,Good Dimensional Stability,Good liquidity,Crystal,Grease resistance,Solvent resistance,Fuel resistance |
| Availabilitys | Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.36 | g/cm³ | ISO 1183-2 |
| Water absorption rate | ISO 62 2 | ||
| saturated | 6.3 | % | ISO 62-2 |
| balance | 1.8 | % | ISO 62-2 |
| Viscosity number | 150 | cm³/g | ISO 307, 1157, 1628 2 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 4100 | MPa | ISO 527-2 2 |
| tensile strength | |||
| fracture | 75.0 | MPa | ISO 527-2 2 |
| Tensile strain | |||
| fracture | 15 | % | ISO 527-2 2 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA 2 | ||
| -30℃ | 3.00 | kJ/m² | ISO 179/1eA 2 |
| 23℃ | 3.00 | kJ/m² | ISO 179/1eA 2 |
| Charpy impact strength | ISO 179/1eU 2 | ||
| -30℃ | 30.0 | kJ/m² | ISO 179/1eU 2 |
| 23℃ | 40.0 | kJ/m² | ISO 179/1eU 2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ISO 75-2 2 | ||
| 0.45 MPa | 180 | ℃ | ISO 75-2 2 |
| 1.8 MPa | 70.0 | ℃ | ISO 75-2 2 |
| Melting temperature | |||
| DSC | 220 | ℃ | ISO 3146 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+15 | ohms·cm | IEC 60093 2 |
| Dielectric constant | |||
| 1 MHz | 3.50 | IEC 60250 | |
| Dissipation factor | |||
| 1 MHz | 0.020 | IEC 60250 2 | |
| Compared to the leakage tracing index | 500 | IEC 60112 2 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |