| About |
|---|
| Plaslube® PC GF30 TL15 is a Polycarbonate (PC) product filled with 30% glass fiber. It can be processed by injection molding and is available in North America. Characteristics include: Flame Rated Lubricated&& |
| Product Description | |
|---|---|
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Features | Lubricating,V-1 |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.55 | g/cm³ | ASTM D792 |
| Water absorption rate | |||
| 24hr | 0.060 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃，3.2mm | 110 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 143 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed | 146 | ℃ | ASTM D648 |
| Linear coefficient of thermal expansion | |||
| MD | 2.9E-5 | 1/℃ | ASTM D696 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50 mm | V-1 | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| fracture | 121 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 5.0 | % | ASTM D638 |
| Bending modulus | 7580 | MPa | ASTM D790 |
| bending strength | 159 | MPa | ASTM D790 |
| friction coefficient | ASTM D1894 | ||
| Steel – Dynamic | 0.20 | ASTM D1894 | |
| Steel – Static | 0.18 | ASTM D1894 | |
| Wear factor | 60 | 10^-8 mm³/N·m | ASTM D3702 |
| Rockwell hardness | |||
| R-level | 116 | ASTM D785 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 121 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Recommended maximum moisture content | 0.10 | % | |
| Barrel rear temperature | 302 to 316 | °C | |
| Barrel middle temperature | 316 to 332 | °C | |
| Barrel front temperature | 310 to 327 | °C | |
| Nozzle temperature | 310 to 327 | °C | |
| Processing (melt) temperature | 304 to 327 | °C | |
| Mold temperature | 71 to 88 | °C | |
| Injection speed | Moderate | ||
| Back pressure | 0.00 to 0.689 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |