VALOX™ IQ420HP resin

About
环保型低碳足迹Valox iQ 树脂 – Valox iQ420HP树脂采用iQ-PBT树脂和30％玻璃纤维增强。 Valox * iQ420HP可用于生产旨在重复使用（而不是单次使用）的食品接触物品，与所有食品类型接触，并且根据FDA食品种类表不符合条件，辐照和烹饪除外 /在250°F以上的温度下烘烤。这包括在这些相同的温度限制条件下的微波。如果将着色剂加入到树脂中，则必须分开评估它们是否适合食品接触应用

About

环保型低碳足迹Valox iQ *树脂 – Valox * iQ420HP树脂采用iQ-PBT树脂和30％玻璃纤维增强。 Valox * iQ420HP可用于生产旨在重复使用（而不是单次使用）的食品接触物品，与所有食品类型接触，并且根据FDA食品种类表不符合条件，辐照和烹饪除外 /在250°F以上的温度下烘烤。这包括在这些相同的温度限制条件下的微波。如果将着色剂加入到树脂中，则必须分开评估它们是否适合食品接触应用

Product Description
Supplier	SABIC
Generic	polybutylene terephthalate
Material Status	Commercial: Active
Features	Food contact compliance,Glass fiber reinforced

Technical Data
MECHANICAL	Nominal value	Unit	Test method
Tensile strain
Yield, 1.3 mm/min, 50 mm span	1.6	%	ISO 527
Fracture, 1.3 mm/min, 50 mm span	1.6	%	ISO 527
Tensile modulus
1 mm/min	10700	MPa	ISO 527
bending strength
Yield, 2 mm/min	210	MPa	ISO 178
Bending modulus
2 mm/mim	9100	MPa	ISO 178

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	80	J/m	ASTM D256
-30℃	80	J/m	ASTM D256
Notched impact strength of cantilever beam
23℃	780	J/m	ASTM D4812
Instrument control anti impact total energy 23 ℃	71	cm-kgf	ASTM D3763
Impact strength of cantilever beam notch
23℃	8	kJ/m²	ISO 180-1A
-30℃，80104	8	kJ/m²	ISO 180-1A
Charpy Notched Impact Strength
80104	14	kJ/m²	ISO 179/1eA

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
1.8 MPa, unannealed, 64 mm span	205	℃	ISO 75/Af
1.8 MPa, unannealed, 3.2 mm	203	℃	ASTM D648
Linear coefficient of thermal expansion
MD：-40~40℃	2.5E-05	1/℃	ASTM E831
TD：-40~40℃	8.9E-05	1/℃	ASTM E831
MD：-40~40℃	2.5E-05	1/℃	ISO 11359-2
TD：-40~40℃	8.9E-05	1/℃	ISO 11359-2
Vicat Softening Temp
B50	206	℃	ASTM D1525
B50	206	℃	ISO 306
B120	206	℃	ISO 306
Ball pressure test
Maximum approximation value	200	℃	IEC 60695-10-2

PHYSICAL	Nominal value	Unit	Test method
Density	1.54	g/cm³	ASTM D792
Shrinkage rate
MD：3.2 mm	0.5-0.7	%	Internal Method
Melt Flow Rate
250℃，5.0kg	52	g/10min	ASTM D1238
Density	1.54	g/cm³	ISO 1183
Water absorption rate
Saturation, 23 ℃	0.09	%	ISO 62
23℃，50% RH	0.1	%	ISO 62
Melt Volume Rate
250℃，5 kg	38	cm³/10min	ISO 1133

Electrical performance	Nominal value	Unit	Test method
Volume resistivity	>1.E+15	ohms·cm	ASTM D257
Dielectric strength
3.2 mm in air	23	kV/mm	ASTM D149
High voltage arc marking rate {PLC	2	PLC Code	UL 746A
Compared to the leakage tracing index	2	PLC Code	UL 746A

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
0.84mm	HB		UL 94

Process Conditions
injection molding	Nominal value	Unit	Test method
Drying temperature	120	°C
Drying time	3-4	hrs
Drying time (gradually increasing)	12	hrs
Maximum water content	0.02	%
Melt temperature	250 – 265	°C
Nozzle temperature	245 – 260	°C
Front temperature	250 – 265	°C
Mid section temperature	245 – 260	°C
Post stage temperature	240 – 255	°C
Mold temperature	65-90	°C
Back pressure	0.3 – 0.7	MPa
Screw speed	50-80	rpm
Shooting cylinder size	40 – 80	%
Depth of exhaust groove	0.025 – 0.038	mm

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.