| About |
|---|
| Ferro PP TPP30AD69BK is a Polypropylene Homopolymer (PP Homopolymer) product filled with 30% talc. It can be processed by injection molding and is available in Latin America or North America. Primary characteristic: homopolymer.&& |
| Product Description | |
|---|---|
| Supplier | Ferro |
| Generic | PP homopolymerization |
| Material Status | Commercial: Active |
| Features | Homopolymer |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.14 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 14 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| TD | 1.5 | % | ASTM D955 |
| MD | 1.3 | % | ASTM D955 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 75 | ASTM D2240 | |
| tensile strength | |||
| 23℃ | 33.1 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 23 ℃ | 12 | % | ASTM D638 |
| Bending modulus | ASTM D790 | ||
| 1% secant, 23 ℃ | 2940 | MPa | ASTM D790 |
| Tangent, 23 ℃ | 3540 | MPa | ASTM D790 |
| bending strength | |||
| 23℃ | 55.8 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 21 | J/m | ASTM D256 |
| 23℃ | 300 | J/m | ASTM D4812 |
| Drop hammer impact | |||
| 23℃ | 1.13 | J | ASTM D5420 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 79.4 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed | 129 | ℃ | ASTM D648 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 93 | °C | |
| Drying time | 2.0 to 3.0 | hr | |
| Barrel rear temperature | 204 to 210 | °C | |
| Barrel middle temperature | 210 to 213 | °C | |
| Barrel front temperature | 213 to 216 | °C | |
| Nozzle temperature | 216 to 218 | °C | |
| Mold temperature | 43 to 54 | °C | |
| Back pressure | 0.138 to 0.345 | MPa | |
| Screw speed | 100 to 150 | rpm | |
| Clamping force | 2.8 to 4.1 | kN/cm² | |
| Screw length to diameter ratio | 20.0:1.0 | ||
| Screw compression ratio | 2.0:1.0 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |