| About |
|---|
| Westlake ELEVATE™ EF529AA is an ethylene vinyl acetate copolymer with 18.5% VA. EF529AA does not contain slip or antiblock, and is designed for blown and cast films requiring excellent optics and low heat seal initiation. High melt strength makes EF529AA an excellent choice for profile extrusions, molding, and foaming applications requiring medium VA content. Application/Uses: Flexible packaging films Peelable seals, adhesive layers Injection and blow molding Profile extrusions, tubing, wire & cable&& |
| Product Description | |
|---|---|
| Supplier | Westlake Chemical |
| Generic | EVA |
| Material Status | Commercial: Active |
| Features | Good heat sealing,Optical performance,Good melt strength,Copolymer |
| Availabilitys | North America,Asia Pacific |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.940 | g/cm³ | ASTM D1505 |
| Melt Flow Rate | 2.5 | g/10min | ASTM D1238 |
| Vinyl acetate content | 18.5 | wt% | |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 32 | µm | |
| Secant modulus | ASTM D882 | ||
| 1% secant, MD: 32 µ m, blow molded film | 42.1 | MPa | ASTM D882 |
| 1% secant, TD: 32 µ m, blow molded film | 50.3 | MPa | ASTM D882 |
| tensile strength | ASTM D882 | ||
| MD, fracture, 32 µ m, blow molded film | 24.8 | MPa | ASTM D882 |
| TD, fracture, 32 µ m, blow molded film | 24.1 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD, fracture, 32 µ m, blow molded film | 600 | % | ASTM D882 |
| TD, fracture, 32 µ m, blow molded film | 800 | % | ASTM D882 |
| Drop hammer impact | |||
| 32 µ m, blow molded film | 290 | g | ASTM D1709 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | 67.0 | ℃ | ASTM D1525 |
| Melting peak temperature | 85.0 | ℃ | ASTM D3418 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 45 °, 31.8 µ m, blow molded film | 82 | ASTM D2457 | |
| Haze | |||
| 31.8 µ m, blow molded film | 3.6 | % | ASTM D1003 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Blown Film Melt Temperature | < 177 | ℃ | |
| < 204 | ℃ |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Test run at 23°C (73°F) and 50% relative humidity |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |