FLEXOMER™ ETS-9066 NT 7

About
FLEXOMER™ ETS -9066 NT 7 Very Low Density Polyethylene (VLDPE) Resin is intended for use in single or multi-layer blown-film constructions or thick sheets. Films extruded from ETS- 9066 NT 7 have a high tear strength, high impact strength, and high puncture resistance and are readily heat sealable. Addition of slip and antiblock agents should be considered for most applications. Excellent strength and toughness balance Flexible over wide temperature range Superior low temperature properties Broad sealing temperature range Complies with U.S. FDA 21 CFR 177.1520 (c) 3.1a (with restrictions) An additive present in this product limits use only in film form for food contact applications. Consult the regulations for complete details.&&

About

FLEXOMER™ ETS -9066 NT 7 Very Low Density Polyethylene (VLDPE) Resin is intended for use in single or multi-layer blown-film constructions or thick sheets. Films extruded from ETS- 9066 NT 7 have a high tear strength, high impact strength, and high puncture resistance and are readily heat sealable. Addition of slip and antiblock agents should be considered for most applications. Excellent strength and toughness balance Flexible over wide temperature range Superior low temperature properties Broad sealing temperature range Complies with U.S. FDA 21 CFR 177.1520 (c) 3.1a (with restrictions) An additive present in this product limits use only in film form for food contact applications. Consult the regulations for complete details.&&

Product Description
Supplier	DOW
Generic	VLDPE
Material Status	Commercial: Active
Availabilitys	North America,Asia Pacific

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.905	g/cm³	ASTM D792
Melt Flow Rate
190℃，2.16kg	0.50	g/10min	ASTM D1238

film	Nominal value	Unit	Test method
film thickness
test	25	µm
Membrane puncture strength	4.52	J	Internal Method
Membrane puncture force	53.4	N	Internal Method
Membrane puncture resistance	29.8	J/cm³	Internal Method
Membrane strength
MD	47.2	J/cm³	ASTM D892
TD	59.6	J/cm³	ASTM D882
Secant modulus			ASTM D882
1% secant, MD	130	MPa	ASTM D882
2% secant, MD	112	MPa	ASTM D882
1% secant, TD	129	MPa	ASTM D882
2% secant, TD	110	MPa	ASTM D882
tensile strength			ASTM D882
MD, yield	6.89	MPa	ASTM D882
TD, yield	6.21	MPa	ASTM D882
MD, fracture	34.1	MPa	ASTM D882
TD, fracture	25.8	MPa	ASTM D882
Tensile strain			ASTM D882
MD, fracture	330	%	ASTM D882
TD, fracture	560	%	ASTM D882
Drop hammer impact	870	g	ASTM D1709B
Elmandorf tear strength			ASTM D1922
MD	270	g	ASTM D1922
TD	440	g	ASTM D1922

THERMAL	Nominal value	Unit	Test method
Vicat Softening Temp	87.8	℃	ASTM D1525
Melting temperature
DSC	99.0	℃	Internal Method

optical performance	Nominal value	Unit	Test method
gloss
45°	48		ASTM D2457
Haze	11	%	ASTM D1003

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.