TITANPRO® PD701

About
Polypropylene homopolymer.The base resin meets the requirements of the U.S. Food and Drug Administration as specified in 21 CFR 177.1520(a)(1)(i) and (c)1.1a. The adjuvant meet their respective FDA regulations and 21 CFR 177.1520(b). In summary, this resin meets the FDS criteria covering safe use of polyolefin articles and component of articles intended for food contact use. The base resin also tested and certified compliant with United States Pharmacopoeia (USP) Class VI standard. TSCA Registry: CAS# 9003-07-0 APPLICATIONS: Extrusion coating on fabrics woven, thin walled molded articles. Characteristics: Low neck in. high temperature resistance and good resistance to pinholing, high gloss and surface hardness, abrasion resistance and excellent moisture barrier, excellent grease and chemical resistance and low odor and taste. FABRICATION: Equipment – general extrusion or injection molding machines and techniques – standard processing.&&

About

Polypropylene homopolymer.The base resin meets the requirements of the U.S. Food and Drug Administration as specified in 21 CFR 177.1520(a)(1)(i) and (c)1.1a. The adjuvant meet their respective FDA regulations and 21 CFR 177.1520(b). In summary, this resin meets the FDS criteria covering safe use of polyolefin articles and component of articles intended for food contact use. The base resin also tested and certified compliant with United States Pharmacopoeia (USP) Class VI standard. TSCA Registry: CAS# 9003-07-0 APPLICATIONS: Extrusion coating on fabrics woven, thin walled molded articles. Characteristics: Low neck in. high temperature resistance and good resistance to pinholing, high gloss and surface hardness, abrasion resistance and excellent moisture barrier, excellent grease and chemical resistance and low odor and taste. FABRICATION: Equipment – general extrusion or injection molding machines and techniques – standard processing.&&

Product Description
Supplier	LOTTE
Generic	PP homopolymerization
Material Status	Commercial: Active
Features	Good surface appearance,Low shrinkage,Food contact compliance,High Heat Resistance,Low odor,Moisture resistance,Good wear resistance,Grease resistance,Solvent resistance,Homopolymer
Availabilitys	Asia Pacific
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.900	g/cm³	ASTM D1505
Melt Flow Rate
230℃，2.16kg	30	g/10min	ASTM D1238
Water absorption rate
24hr	0.020	%	ASTM D570

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	32	J/m	ASTM D256-A

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	90.0	℃	ASTM D648

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
R-level	98		ASTM D785
tensile strength
yield	31.4	MPa	ASTM D638
Tensile strain
yield	12	%	ASTM D638
Bending modulus	1320	MPa	ASTM D790B

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.