| About |
|---|
| DURAFIDE® 1140A64 is a Polyphenylene Sulfide (PPS) product filled with 40% glass fiber. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America. Primary characteristic: flame rated.&& |
| Product Description | |
|---|---|
| Supplier | Polyplastics |
| Generic | PPS |
| Material Status | Commercial: Active |
| Features | Low flash,V-0 |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| tensile strength | 200 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 1.8 | % | ISO 527-2 |
| Bending modulus | 14000 | MPa | ISO 178 |
| bending strength | 280 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | 9.5 | kJ/m² | ISO 179-1eA |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 270 | ℃ | ISO 75-2/A |
| Linear coefficient of thermal expansion | |||
| MD | 2.0E-5 | 1/℃ | |
| TD | 4.0E-5 | 1/℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 4.0E+16 | ohms·cm | IEC 60093 |
| Dielectric strength | |||
| 3 mm | 16 | kV/mm | IEC 60243-1 |
| Dielectric constant | IEC 60250 | ||
| 1 kHz | 4.50 | ||
| 1 MHz | 4.50 | ||
| Dissipation factor | IEC 60250 | ||
| 1 kHz | 1.0E-3 | ||
| 1 MHz | 2.0E-3 | ||
| Arc resistance | 123 | sec | |
| Compared to the leakage tracing index | 150 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | V-0 | UL 94 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Color Number | HF2000/HD9100 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.66 | g/cm³ | ISO 1183 |
| Water absorption rate | |||
| 23℃，24hr | 0.040 | % | ISO 62 |
| Apparent viscosity of melt | |||
| 310℃，1000 sec^-1 | 240 | Pa·s | ISO 11443 |
| Process Conditions | |||
|---|---|---|---|
| injection molding | Nominal value | Unit | Test method |
| Drying time | 3 | hrs | |
| drying temperature | 140 | ℃ | |
| Roller temperature – Zone 1 | 290~300 | ℃ | |
| Roller temperature – Zone 2 | 300 | ℃ | |
| Roller temperature – Zone 3 | 310 | ℃ | |
| Roller temperature – Zone 4 | 310 | ℃ | |
| Nozzle temperature | 310~320 | ℃ | |
| Forming temperature | 150 | ℃ | |
| Injection pressure | 40~70 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |