Ultramid® A 205F NATURAL

About
TECHNYL® A 205F Natural is an unreinforced polyamide 66 for injection moulding. This grade offers two main advantages: excellent filling qualities and UL 94 V2 under 0.4 mm. It is particularly suitable for the moulding of long parts with thin wall sections&&

Product Description
Supplier	BASF
Generic	PA66
Material Status	Commercial: Active
Features	Quick molding cycle,V-2,High liquidity
Availabilitys	Europe,Latin America,North America,Asia Pacific,Africa & Middle East
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Mold Shrinkage
Parallel	1.7	%	ISO 294-4
Normal	1.7	%	ISO 294-4
Water Absorption
24 h，23℃	1.3	%	ISO 62
Moisture Absorption
Equilibrium, 23 ℃. 50% r. h	3.0	%	ISO 62
Density	1140	kg/m³	ISO 1183

MECHANICAL	Nominal value	Unit	Test method
Tensile Modulus
Dry	3200	MPa	ISO 527
Wet Cond	1400	MPa	ISO 527
Tensile Strength
50 mm/min, dry	85	MPa	ISO 527-2
50 mm/min, moist cond	50	MPa	ISO 527-2
Yield yld, 2 in/min, dry dry	85	MPa	ASTM D638
Broken BRK, dry dry	60	MPa	ISO 527-2
Broken BRK, wet Cond	40	MPa	ISO 527-2
Tensile Strain
50 mm/min, dry	4	%	ISO 527
50 mm/min, moist cond	10	%	ISO 527
Broken BRK, dry dry	50	%	ISO 527
Broken BRK, wet Cond	250	%	ISO 527
Elongation at Break	25	%	ASTM D638
Flexural Modulus
Dry	3000	MPa	ISO 178
Wet Cond	1300	MPa	ISO 178
Dry	3350	MPa	ASTM D790
Flexural Strength
Dry	120	MPa	ISO 178
Wet Cond	50	MPa	ISO 178
Dry	125	MPa	ISO 178

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength
Dry	5	kJ/m²	ISO 179/1eA
Wet Cond	10	kJ/m²	ISO 179/1eA
Izod Notched Impact strength
Dry	5	KJ/m²	ISO 180/1A
Wet Cond	8	KJ/m²	ISO 180/1A
Dry	80	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature HDT
0.45 MPa	205	℃	ISO 75-1/-2
1.80 MPa	65	℃	ISO 75-1/-2
1.8 MPa	80	℃	ASTM D648
0.45 MPa	80	℃	ASTM D648
Melting temperature	263	℃	ISO 11357-3

ELECTRICAL	Nominal value	Unit	Test method
Surface Resistivity
Dry	5E15	ohm	IEC 62631-3-2
Wet Cond	1E14	ohm	IEC 62631-3-2
Volume Resistance
Dry	1E13	ohm·m	IEC 62631-3-1
Wet Cond	1E13	ohm·m	IEC 62631-3-1
Electric strength
d=0.8 mm	35	kV/mm	IEC 60243-1
d=2.0 mm	22	kV/mm	IEC 60243-1
Dielectric Constant
1 MHz	3.5		IEC 62631-2-1
Dissipation Factor
1 MHz	0.033	E-4	IEC 62631-2-1
Compared Tracking Index
Test solution A, dry dry	600		IEC 60112
Test solution A, moisten cond	600		IEC 60112
Test solution B, dry dry	550		IEC 60112

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame Class Rating
1.6 mm	V-2	calss	IEC 60695-11-10
0.4 mm	V-2	calss	IEC 60695-11-10
0.8 mm	V-2	calss	UL-94, IEC 60695
3.2 mm	V-2	calss	UL-94, IEC 60695
Glow Wire Flammability Index (GWFI)
1.6 mm	800	℃	IEC 60695-2-12
Oxygen Index	28	%	ISO 4589-2

Process Conditions
Injection Molding	Nominal value	Unit	Test method
Drying Temperature	80	℃
Drying Time	0.2	hr
Front Temperature Zone 3	265-275	℃
Middle Temperature Zone 2	270-280	℃
Rear Temperature Zone 1	280-285	℃
Mold Temperature	60-80	℃	ISO 294

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.