| About |
|---|
| Kingfa PA66-G30 HSBK161 is a Polyamide 66 (Nylon 66) material filled with 30% glass fiber. It is available in Asia Pacific or North America for injection molding. Important attributes of Kingfa PA66-G30 HSBK161 are: Flame Rated Good Aesthetics Good Dimensional Stability Heat Resistant High Strength Typical application of Kingfa PA66-G30 HSBK161: Automotive&& |
| Product Description | |
|---|---|
| Supplier | Kingfa |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good surface appearance,Good Dimensional Stability,Heat Resistance, Good |
| Availabilitys | North America,Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.36 | g/cm³ | |
| Shrinkage rate | |||
| TD | 0.90 | % | |
| MD | 0.30 | % | |
| Water absorption rate | |||
| Equilibrium, 23 ℃, 50% RH | 1.6 | % | |
| Ash Content | 30 | % | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 12 | kJ/m² |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 255 | ℃ | |
| 1.8 MPa, unannealed | 250 | ℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+15 | ohms·cm |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.60 mm | HB |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Ball hardness | 240 | MPa | |
| Tensile modulus | 9500 | MPa | |
| tensile strength | 190 | MPa | |
| Tensile strain | |||
| fracture | 3.0 | % | |
| Bending modulus | 8800 | MPa | |
| bending strength | 270 | MPa |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 100 to 130 | °C | |
| Drying time | 4.0 to 6.0 | hr | |
| Barrel rear temperature | 270 to 285 | °C | |
| Barrel middle temperature | 280 to 290 | °C | |
| Barrel front temperature | 290 to 300 | °C | |
| Processing (melt) temperature | 270 to 290 | °C | |
| Mold temperature | 40 to 100 | °C | |
| Injection speed | 中等偏快 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 3. 23°C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |