| About |
|---|
| Veradel 3330GF是一种30％玻纤增强级聚醚砜（PESU ）。在聚醚砜中添加玻璃纤维后，大幅提高了材料的刚性、拉伸强度、耐蠕变性、尺寸稳定性和耐化学性，同时其它大部分基本特征保持不变。结构性能和成本效益的有利结合，使这种树脂成为许多工程应用极有吸引力的金属替代材料。 自然状态的Veradel 3330GF PESU是一种浅灰色的材料，易于着色。 该牌号原来以Gafone™ PESU销售。&& |
| Product Description | |
|---|---|
| Supplier | Solvay |
| Generic | PES |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good flexibility,Good Dimensional Stability,Hydrolysis stability,Flame Characteristics,Acidproof,High Heat Resistance,Good bond,Good Tensile Strength,Moderate liquidity,Solvent resistance,Heat Stabilized,V-0 |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.58 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 343℃，2.16kg | 4.5 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD | 0.30 | % | ASTM D955 |
| Water absorption rate | |||
| 24hr | 0.40 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 8620 | MPa | ASTM D638 |
| tensile strength | 130 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 1.9 | % | ASTM D638 |
| Bending modulus | 8620 | MPa | ASTM D790 |
| bending strength | 179 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 75 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 216 | ℃ | ASTM D648 |
| Linear coefficient of thermal expansion | |||
| MD | 3.1E-5 | 1/℃ | ASTM D696 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | > 1.0E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | 17 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 60 Hz | 4.11 | ||
| 1 kHz | 4.13 | ||
| 1 MHz | 4.17 | ||
| Dissipation factor | ASTM D150 | ||
| 60 Hz | 1.9E-3 | ||
| 1 kHz | 1.8E-3 | ||
| 1 MHz | 9.4E-3 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 0.787 mm | V-0 | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 149 to 177 | °C | |
| Drying time | 2.5 to 4.0 | hr | |
| Processing (melt) temperature | 343 to 399 | °C | |
| Mold temperature | 149 to 163 | °C | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |