| About |
|---|
| Kingfa PA66-NPG30 is a Polyamide 66 (Nylon 66) material filled with 30% glass fiber. It is available in Asia Pacific or North America for injection molding. Important attributes of Kingfa PA66-NPG30 are: Flame Rated Flame Retardant Halogen Free Typical application of Kingfa PA66-NPG30: Electrical/Electronic Applications&& |
| Product Description | |
|---|---|
| Supplier | Kingfa |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | Flame Characteristics,Low to no phosphorus content,Low smoke,Good Electrical Properties,Halogen free |
| Availabilitys | Asia Pacific,North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Tensile Strength | 140 | MPa | ISO 527-2 |
| Tensile Strain | |||
| Broken BRK | 2.5 | % | ISO 527 |
| Flexural Strength | 200 | MPa | ISO 178 |
| Flexural Modulus | 9000 | MPa | ISO 178 |
| Rockwell hardness | 120 | ISO 2039-2 | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Izod Notched Impact strength | 9 | KJ/m² | ISO 180/1A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature HDT | |||
| 0.45 MPa | 250 | ℃ | ISO 75-1/-2 |
| 1.80 MPa | 240 | ℃ | ISO 75-1/-2 |
| ELECTRICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume Resistance | 1E15 | ohm·cm | IEC 60093 |
| Compared Tracking Index | 600 | V | IEC 60112 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.41 | g/cm³ | ISO 1183 |
| Molding shrinkage | |||
| Flow | 0.3-0.5 | % | ISO 294-4 |
| Transverse | 0.8-1.0 | % | ISO 294-4 |
| Water Absorption | |||
| equilibrium | 1.5 | % | ISO 62 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame Class Rating | V-0 | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| Injection Molding | Nominal value | Unit | Test method |
| Drying Temperature | 90-110 | °C | |
| Drying Time | 4-6. | hr | |
| Melt Temperature | 260-290 | °C | |
| Rear Temperature Zone 1 | 250-265 | °C | |
| Middle Temperature Zone 2 | 265-275 | °C | |
| Front Temperature Zone 3 | 270-280 | °C | |
| Mold Temperature | 60-90 | °C | |
| Injection speed | 中等偏快 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |