| About |
|---|
| CYROLITE® MD H12 acrylic polymer is an amorphous thermoplastic molding compound based on polymethyl methacrylate (PMMA) for the medical diagnostic industry. Typical properties of CYROLITE® MD acrylic polymers are: exceptional ultra-violet light transmittance (UVT) exceptional optical clarity good dimensional stability for controlled fluid flow The special properties of CYROLITE® MD H12 polymer are: medium heat resistance medium melt flow rate UV light transmitting Application: Used for injection molding of medical devices requiring UV spectroscopy for fluid evaluation.&& |
| Product Description | |
|---|---|
| Supplier | ROHM |
| Generic | PMMA |
| Material Status | Commercial: Active |
| Features | Good Clarity,Good Dimensional Stability,Food contact compliance,Moderate liquidity,Heat Resistance, Good,Amorphous |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.19 | g/cm³ | ASTM D792 |
| Apparent density | 0.66 | g/cm³ | ASTM D1895 |
| Melt Flow Rate | |||
| 230℃，3.80kg | 7.0 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD | 0.40 to 0.60 | % | ASTM D955 |
| Water absorption rate | |||
| balance | < 0.30 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃，6.4mm | 19 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed, 6.35 mm | 93.9 | ℃ | ASTM D648 |
| Vicat Softening Temp | 105 | ℃ | ASTM D1525 |
| Linear coefficient of thermal expansion | |||
| MD：0~156℃ | 7.2E-5 | 1/℃ | ASTM D696 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Transmittance | |||
| 3200 µm | 92.0 | % | ASTM D1003 |
| Haze | |||
| 3200 µm | < 1.0 | % | ASTM D1003 |
| Yellowness index | |||
| 3.20 mm | < 1.0 | YI | ASTM D1925 |
| UV transmittance (3.20 mm) | > 88 | % | ASTM D1003 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| M-level | 94 | ASTM D785 | |
| Tensile modulus | 3240 | MPa | ASTM D638 |
| tensile strength | 65.5 | MPa | ASTM D638 |
| Tensile strain | ASTM D638 | ||
| yield | 4.0 to 6.0 | % | ASTM D638 |
| fracture | 4.0 to 6.0 | % | ASTM D638 |
| Bending modulus | 3380 | MPa | ASTM D790 |
| bending strength | 117 | MPa | ASTM D790 |
| Notes |
|---|
| 1. Colorless only |
| 2. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |