Addisil™ 2050 E

About
The Addisil 20X0 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications. Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odourless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test&&

About

The Addisil 20X0 E series is a two-component heat curable rubber for making elastomers (HCE) with a hardness range between 50 and 80 Shore A for industrial applications. This series is based on a platinum cure system, which is particularly suitable for high value extrusion applications where regulatory compliance, transparency, mechanical performance and/or productivity are important. Application examples are oven door profiles and tubing for food applications. Key Features and Benefits Good transparency, no yellowing Good mechanical performance Dry, non-stick surface Odourless during processing and in its application Fast curing Long shelf life of 6 months for the single components if stored appropriatelyM Very long pot life of 2 to 4 weeks for the mixed components Suitable for compliance with the food contact regulations FDA 21 CFR 177.2600 and the BfR section XV recommendations KTW: German Water Regulation. A representative sample has passed the test for tubes, fittings, seals and strorage systems (cold and warm) WRAS (BS 6920). A representative sample has passed the test (cold and warm) W270: Microbiological growth test. A representative sample has passed the test&&

Product Description
Supplier	Momentive
Generic	硅橡胶
Material Status	Commercial: Active
Features	No viscosity,Food contact compliance,Low odor,Baking,Fast Cure
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.15	g/cm³	DIN 53479

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s A	48		DIN 53505

elastic body	Nominal value	Unit	Test method
tensile strength	10.0	MPa	DIN 53504
Tensile strain
fracture	700	%	DIN 53504
tear strength	32.0	kN/m	ASTM D624
Compression deformation
175℃，22 hr	25	%	DIN 53517

THERMAL	Nominal value	Unit
Thermosetting components
Component A	按重量计算的混合比: 1.0
Component B	按重量计算的混合比: 1.0
storage stability	20000 to 40000	min
Storage period	26	wk
Post curing time
200℃	4.0	hr

Supplementary information	Nominal value	Unit	Test method
Vulcanization（175℃）	10.0	min

Notes
1. Typical properties: these are not to be construed as specifications.
2. Die B
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.