| About |
|---|
| ADIPRENE LF 1930A is a TDI-terminated polyester prepolymer having very low free TDI content. This prepolymer also has low viscosity, which allows it to be processed at reduced temperature for better heat stability and longer pot life. It yields a high performance 93 Shore A hardness elastomer when cured with 4,4′-methylene-bis-[o-chloroaniline], commonly called MBCA. Features of ADIPRENE LF 1930A include: Low Free TDI Content Low Viscosity Long Pot Life High Tear and Tensile Strength&& |
| Product Description | |
|---|---|
| Supplier | Chemtura |
| Generic | PUR-酯+TDI |
| Material Status | Commercial: Active |
| Features | Low Viscosity,Good Tensile Strength,Good tear strength,Good wear resistance |
| Availabilitys | North America,Latin America,Asia Pacific,Europe |
| Process Methods | casting |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.28 | g/cm³ | ASTM D792 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| Pant tear resistance | 64.8 | N/mm | ASTM D1938 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ASTM D412 | ||
| 100% strain | 11.7 | MPa | ASTM D412 |
| 200% strain | 15.2 | MPa | ASTM D412 |
| 300% strain | 22.1 | MPa | ASTM D412 |
| tensile strength | 50.0 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 490 | % | ASTM D412 |
| tear strength | |||
| — | 121 | kN/m | ASTM D624 |
| cracking | 28 | kN/m | ASTM D470 |
| Compression deformation | |||
| 70℃，22 hr | 33 | % | ASTM D395B |
| Basho’s elasticity | 27 | % | ASTM D2632 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| storage stability | 6.0 to 8.0 | min | |
| stripping time | 25 to 35 | min |
| Uncured Properties | Nominal value | Unit | Test method |
|---|---|---|---|
| Curing time | |||
| 100℃ | 6.0 | hr |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 92 to 94 | ASTM D2240 | |
| compressive strength | ASTM D695 | ||
| 5% strain | 2.55 | MPa | ASTM D695 |
| 10% strain | 4.00 | MPa | ASTM D695 |
| 15% strain | 5.52 | MPa | ASTM D695 |
| 20% strain | 7.58 | MPa | ASTM D695 |
| 25% strain | 10.3 | MPa | ASTM D695 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |