AEI SX523:CM493 and SX523:CM497

About
UV stabilised silane crosslinkable polyethylene compound for “Câble Torsadé” overhead power cable insulation This is a chemically crosslinkable polyethylene compounds for insulation of cables where resistance to ultra-violet radiation is required. The material is carbon loaded and possesses excellent extrusion properties at high output rates. The graft component SX523 is mixed with a crosslinking catalyst masterbatch CM493 or CM497 generally in the ratio 95:5 and is curable by exposure to moist conditions. The compound has been specially developed for the “Câble Torsadé” NFC 33-209 specification for overhead power cable applications.&&

About

UV stabilised silane crosslinkable polyethylene compound for “Câble Torsadé” overhead power cable insulation This is a chemically crosslinkable polyethylene compounds for insulation of cables where resistance to ultra-violet radiation is required. The material is carbon loaded and possesses excellent extrusion properties at high output rates. The graft component SX523 is mixed with a crosslinking catalyst masterbatch CM493 or CM497 generally in the ratio 95:5 and is curable by exposure to moist conditions. The compound has been specially developed for the “Câble Torsadé” NFC 33-209 specification for overhead power cable applications.&&

Product Description
Generic	LDPE
Material Status	Commercial: Active
Features	Weather resistance is good,Crosslinked
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.950	g/cm³	BS 2782 620A

MECHANICAL	Nominal value	Unit	Test method
tensile strength	18.0	MPa	IEC 60811-1-1
Tensile strain
fracture	450	%	IEC 60811-1-1

Aging performance	Nominal value	Unit	Test method
The rate of change in tensile strength
150℃，240 hr	20	%	IEC 60811-1-2
Changes in tensile stress during fracture
150℃，240 hr	-18	%	IEC 60811-1-2

THERMAL	Nominal value	Unit	Test method
thermosetting			IEC 60811-2-1
Elongation under load: 20 N/cm ²， 200 ℃	80	%	IEC 60811-2-1
Maximum permanent elongation after cooling	5.0	%	IEC 60811-2-1

Electrical performance	Nominal value	Unit	Test method
Volume resistivity
20 ℃	> 1.5E+16	ohms·cm	IEC 60502
Relative permittivity
23℃，50 Hz	3.47		IEC 60250
power factor
50Hz，23℃	0.00170		IEC 60250

Process Conditions
Extrusion	Nominal value	Unit	Test method
Barrel 1 zone temperature	130	°C
Barrel 2 zone temperature	150	°C
Barrel 3 zone temperature	170	°C
Barrel 4 zone temperature	190	°C
Head temperature	200	°C
Nozzle temperature	210	°C

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.