AgriPlast NFLDPE 5050/40000 HM

About
AgriPlast NFLDPE 5050/40000 HM is made up of 50% cellulose fibres obtained from meadow grass and 50% low density polyethylene. AgriPlast BW granules can be used with any injection moulding machine and processed into moulded components such as spoons, consoles, machine cases, protective caps, etc. The granules can also be dyed any colour. Ideal ease of flow for injection moulding. High cycle times when manufacturing complex moulded parts. AgriPlast is lighter than comparable fibre-reinforced composite plastics. Fire protection without antimony and halogen. Recyclable and residue-free disposal when incinerated. Processing Notes for AgriPlast NFLDPE 5050/40000 HM: sufficiently dry at 70 – 80 °C, heating zones of 200 °C decreasing to 170 °C, possible short-term peak melting temperature of 210 °C, moulding temperature of 40 – 50 °C, avoid frictional and shearing heat, make sure the tool is well ventilated.&&

About

AgriPlast NFLDPE 5050/40000 HM is made up of 50% cellulose fibres obtained from meadow grass and 50% low density polyethylene. AgriPlast BW granules can be used with any injection moulding machine and processed into moulded components such as spoons, consoles, machine cases, protective caps, etc. The granules can also be dyed any colour. Ideal ease of flow for injection moulding. High cycle times when manufacturing complex moulded parts. AgriPlast is lighter than comparable fibre-reinforced composite plastics. Fire protection without antimony and halogen. Recyclable and residue-free disposal when incinerated. Processing Notes for AgriPlast NFLDPE 5050/40000 HM: sufficiently dry at 70 – 80 °C, heating zones of 200 °C decreasing to 170 °C, possible short-term peak melting temperature of 210 °C, moulding temperature of 40 – 50 °C, avoid frictional and shearing heat, make sure the tool is well ventilated.&&

Product Description
Generic	LDPE
Material Status	Commercial: Active
Features	Renewable resources,Good liquidity,Halogen free,Flame Characteristics,No antimony
Availabilitys	Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.07	g/cm³	ISO 1183

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus	1050	MPa	ISO 527-2
tensile strength
yield	15.1	MPa
—	15.1	MPa
Tensile strain
yield	2.9	%	ISO 527-2
Tensile Strain at Tensile Strength	2.9	%	ISO 527-2
Bending modulus	1000	MPa	ISO 178
bending strength	22.3	MPa	ISO 178
Bending strain	5.1	%	ISO 178

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength	8.8	kJ/m²	ISO 179
Charpy Unnotch Impact strength	16	kJ/m²	ISO 179

THERMAL	Nominal value	Unit	Test method
Vicat Softening Temp
B50	110	℃	ISO 306

Process Conditions
injection	Nominal value	Unit	Test method
Drying temperature	70 to 80	°C
Processing (melt) temperature	210	°C
Mold temperature	40 to 50	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.