| About |
|---|
| Akulon®是高性能PA6和PA66家族，客户遍布全球，广泛应用于汽车、电子电气、家具、包装等行业。&&我们提供注塑级、吹塑级和挤出级的Akulon®牌号，其中挤出级包括阻隔膜、棒材、波纹管和单层多层膜。&&用此材料注塑时，在设计简单和卓越的机械性能间能达到完美的平衡，应用种类多，温度范围广。用作挤出时，Akulon®的强度、回弹性和加工简便都是市场标杆。 |
| Product Description | |
|---|---|
| Supplier | DSM |
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Low Viscosity,Good stripping performance,Medium Viscosity |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.14 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| TD | 1.1 / * | % | ISO 294-4 |
| Shrinkage rate | |||
| MD | 1.1 / * | % | ISO 294-4 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 3500 / – | MPa | ISO 527-1-2 |
| Yield stress | 85 / – | MPa | ISO 527-1/-2 |
| Tensile strain | |||
| yield | 4 / – | % | ISO 527-1/2 |
| Tensile strain | |||
| fracture | 20 / >50 | % | ISO 527-1/2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | |||
| 10℃ / min | 220 / * | ℃ | ISO 11357-1/-3 |
| Hot deformation temperature | |||
| 1.8 MPa | 60 / * | ℃ | ISO 75-1/2 |
| Hot deformation temperature | |||
| 0.45 MPa | 160 / * | ℃ | ISO 75-1/2 |
| Linear coefficient of thermal expansion | |||
| TD | 0.9E-4 | /℃ | ISO 11359-1/-2 |
| Linear coefficient of thermal expansion | |||
| MD | 1E-4 | /℃ | ISO 11359-1/-2 |
| Combustibility (1.5mm thickness) | V-2 / * | class | IEC 60695-11-10 |
| Test thickness | 3 / * | mm | IEC 60695-11-10 |
| UL certification | Yes / * | – | – |
| Combustibility at a thickness of h | V-2 / * | class | IEC 60695-11-10 |
| The thickness of the test specimen used for testing | 0.75 / * | mm | IEC 60695-11-10 |
| UL certification | Yes / * | – | – |
| Glow wire combustion index GWFI | 960 / – | °C | IEC 60695-2-12 |
| GWFI (thickness (1)) | 1 / – | mm | IEC 60695-2-12 |
| Relative Temperature Index – Electrical | 150 / * | °C | UL746B |
| Relative Temperature Index – Electrical, Thickness 1 | 0.75 / * | mm | UL746B |
| Relative Temperature Index – Electrical | 150 / * | °C | UL746B |
| Relative Temperature Index – Electrical, Thickness 2 | 3 / * | mm | UL746B |
| Relative Temperature Index – Impact | 65 / * | °C | UL746B |
| Relative temperature index – impact, thickness 1 | 0.75 / * | mm | UL746B |
| Relative Temperature Index – Impact | 65 / * | °C | UL746B |
| Relative temperature index – impact, thickness 2 | 3 / * | mm | UL746B |
| Relative temperature index – non impact | 65 / * | °C | UL746B |
| 0.75 / * | mm | UL746B | |
| Relative temperature index | |||
| Non impact | 65 / * | ℃ | UL 746B |
| Relative temperature index | |||
| Non impact, thickness 2 | 3 / * | mm | UL 746B |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Relative permittivity | |||
| 100 Hz | 3.4 / 15 | IEC 60250 | |
| Relative permittivity | |||
| 1 MHz | 3.1 / 4.7 | IEC 60250 | |
| Dissipation factor | |||
| 100 Hz | 65 / 3900 | E-4 | IEC 60250 |
| Dissipation factor | |||
| 100 Hz | 165 / 1300 | E-4 | IEC 60250 |
| Volume resistivity | 1E15 | ohms·cm | IEC 60093 |
| Dielectric strength | 8 / – | kV/mm | IEC 60243-1 |
| Compared to the leakage tracing index | – / 600 | V | IEC 60112 |
| Other performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Water absorption rate | 10 / * | % | ISO 62 |
| Moisture absorption rate | 2.8 / * | % | Sim. to ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | |||
| 23℃ | N / N | kJ/m² | ISO 179/1eU |
| Charpy Unnotch Impact strength | |||
| -30℃ | N / N | kJ/m² | ISO 179/1eU |
| Charpy Notched Impact Strength | |||
| 23℃ | 5 / – | kJ/m² | ISO 179/1eA |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |