| About |
|---|
| 10% Glass Reinforced, 20% Glass Beads Reinforced, Heat Stabilized&& |
| Product Description | |
|---|---|
| Supplier | DSM |
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Heat Stabilized |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Tensile modulus | 6200 | MPa | |
| tensile strength | |||
| fracture | 115 | MPa | |
| Tensile strain | |||
| fracture | 3.0 | % | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| -30℃ | 4.0 | kJ/m² | |
| 23℃ | 4.0 | kJ/m² | |
| Charpy Unnotch Impact strength | |||
| -30℃ | 30 | kJ/m² | |
| 23℃ | 35 | kJ/m² |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 215 | ℃ | |
| 1.8 MPa, unannealed | 195 | ℃ | |
| Melting temperature | 220 | ℃ | |
| Linear coefficient of thermal expansion | |||
| MD | 3.5E-5 | 1/℃ | |
| TD | 9.0E-5 | 1/℃ | |
| Effective Thermal Diffusivity | 1.43E-7 | m²/s |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+14 | ohms·cm | |
| Dielectric strength | 35 | kV/mm | |
| Relative permittivity | |||
| 100 Hz | 3.50 | ||
| 1 MHz | 3.30 | ||
| Dissipation factor | |||
| 100 Hz | 5.0E-3 | ||
| 1 MHz | 0.015 | ||
| Compared to the leakage tracing index | — | V |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flammability level | |||
| 0.75 mm | HB | ||
| 1.5 mm | HB |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.35 | g/cm³ | |
| Melt Volume Rate | |||
| 250℃，2.16 kg | 10.0 | cm³/10min | |
| Shrinkage rate | |||
| TD | 1.2 | % | |
| MD | 0.70 | % | |
| Water absorption rate | |||
| Saturation, 23 ℃ | 6.3 | % | |
| Equilibrium, 23 ℃, 50% RH | 1.9 | % | |
| Melt density | 1.19 | g/cm³ | |
| Melt thermal conductivity | 0.29 | W/m/K | |
| Specific Heat Capacity of Melt | 2230 | J/kg/℃ |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Barrel rear temperature | 255 to 265 | °C | |
| Barrel middle temperature | 265 to 275 | °C | |
| Barrel front temperature | 265 to 280 | °C | |
| Nozzle temperature | 260 to 280 | °C | |
| Processing (melt) temperature | 250 to 285 | °C | |
| Mold temperature | 50 to 80 | °C | |
| Injection speed | 中等偏快 | ||
| Back pressure | 3.00 to 10.0 | MPa | |
| Screw compression ratio | 2.5:1.0 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |