| About |
|---|
| Akulon® S240-CH Inj-Mold is a Polyamide 66 (Nylon 66) material. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America for injection molding. Primary attribute of Akulon® S240-CH Inj-Mold: Flame Rated.&& |
| Product Description | |
|---|---|
| Supplier | DSM |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Availabilitys | North America,Latin America,Europe,Africa & Middle East ,Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Tensile Modulus | 3200 | MPa | |
| Tensile Strength | |||
| Yield yld | 85.0 | MPa | |
| Tensile Strain | |||
| Yield yld | 5.0 | % | |
| Tensile Strain | > 50 | % | |
| Flexural Modulus | 2950 | MPa | |
| Flexural Strength | 117 | MPa | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 10 | kJ/m² | |
| Charpy Unnotch Impact strength | |||
| -30℃ | 无断裂 | ||
| 23℃ | 无断裂 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature HDT | |||
| 0.45 MPa, unannealed | 220 | ℃ | |
| 1.8 MPa, unannealed | 80.0 | ℃ | |
| Melting temperature | 260 | ℃ | |
| Effective Thermal Diffusivity | 4.87E-8 | m²/s |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame Class Rating | |||
| 3.0 mm | V-2 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.14 | g/cm³ | |
| Water Absorption | |||
| Saturation, 23 ℃ | 9.0 | % | |
| Equilibrium, 23 ℃, 50% RH | 2.5 | % | |
| Density | 0.969 | g/cm³ | |
| Melt thermal conductivity | 0.13 | W/m/K | |
| Specific Heat Capacity of Melt | 2750 | J/kg/℃ |
| Process Conditions | |||
|---|---|---|---|
| Injection Molding | Nominal value | Unit | Test method |
| Drying Temperature | 80 | °C | |
| Drying Time | 2.0 to 4.0 | hr | |
| Rear Temperature Zone 1 | 230 to 235 | °C | |
| Middle Temperature Zone 2 | 235 to 250 | °C | |
| Front Temperature Zone 3 | 240 to 260 | °C | |
| Nozzle temperature | 240 to 270 | °C | |
| Melt Temperature | 240 to 275 | °C | |
| Mold Temperature | 50 to 80 | °C | |
| Injection speed | 中等偏快 | ||
| Back Pressure | 3.00 to 10.0 | MPa | |
| Screw Compression Ratio | 2.5:1.0 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |