| About |
|---|
| 10% Glass Reinforced, 20% Mineral Reinforced, Heat Stabilized, High Flow&& |
| Product Description | |
|---|---|
| Supplier | DSM |
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Good liquidity,Heat Stabilized |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Tensile modulus | 7500 | MPa | |
| tensile strength | |||
| fracture | 110 | MPa | |
| Tensile strain | |||
| fracture | 2.3 | % | |
| Bending modulus | 6500 | MPa | |
| bending strength | 165 | MPa | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| -30℃ | 4.0 | kJ/m² | |
| 23℃ | 4.0 | kJ/m² | |
| Charpy Unnotch Impact strength | |||
| -30℃ | 30 | kJ/m² | |
| 23℃ | 35 | kJ/m² |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 210 | ℃ | |
| 1.8 MPa, unannealed | 180 | ℃ | |
| Melting temperature | 220 | ℃ | |
| Linear coefficient of thermal expansion | |||
| MD | 3.5E-5 | 1/℃ | |
| TD | 6.0E-5 | 1/℃ | |
| Effective Thermal Diffusivity | 1.16E-7 | m²/s |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+14 | ohms·cm | |
| Relative permittivity | |||
| 100 Hz | 3.50 | ||
| 1 MHz | 3.30 | ||
| Dissipation factor | |||
| 100 Hz | 5.0E-3 | ||
| 1 MHz | 0.014 | ||
| Compared to the leakage tracing index | 500 | V |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flammability level | |||
| 1.6 mm | HB |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.37 | g/cm³ | |
| Melt Volume Rate | |||
| 250℃，2.16 kg | 20.0 | cm³/10min | |
| Shrinkage rate | |||
| TD | 0.93 | % | |
| MD | 0.40 | % | |
| Water absorption rate | |||
| Saturation, 23 ℃ | 6.5 | % | |
| Equilibrium, 23 ℃, 50% RH | 1.9 | % | |
| Melt density | 1.17 | g/cm³ | |
| Melt thermal conductivity | 0.32 | W/m/K | |
| Specific Heat Capacity of Melt | 2310 | J/kg/℃ |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Barrel rear temperature | 230 to 250 | °C | |
| Barrel middle temperature | 230 to 260 | °C | |
| Barrel front temperature | 230 to 260 | °C | |
| Nozzle temperature | 250 to 280 | °C | |
| Processing (melt) temperature | 250 to 280 | °C | |
| Mold temperature | 40 to 80 | °C | |
| Injection speed | 中等偏快 | ||
| Back pressure | 3.00 to 10.0 | MPa | |
| Screw compression ratio | 2.5:1.0 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |