| About |
|---|
| ALCOM® TCD PA6 5060 FR 16089 is a Polyamide 6 (Nylon 6) product filled with filler. It can be processed by injection molding and is available in Asia Pacific, Europe, or North America. Applications of ALCOM® TCD PA6 5060 FR 16089 include electrical/electronic applications, automotive, engineering/industrial parts, housings and lighting applications. Characteristics include: Flame Rated RoHS Compliant Flame Retardant Conductive Halogen Free&& |
| Product Description | |
|---|---|
| Supplier | ALBIS |
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Good heat aging resistance,Halogen free,Flame Characteristics,Thermal conductivity,Insulation |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.63 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| 24 hrs | > 0.80 | % | ISO 294-4 |
| Spiral flow length | |||
| 2.00 mm | 230 | n | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 9200 | MPa | ISO 527-2 |
| tensile strength | 85.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 1.5 | % | ISO 527-2 |
| Bending modulus | 9500 | MPa | ISO 178 |
| bending strength | 140 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | 30 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 155 | ℃ | ISO 75-2/A |
| Vicat Softening Temp | |||
| B50 | 210 | ℃ | ISO 306 |
| Melting temperature | |||
| DSC | 220 | ℃ | ISO 11357 |
| specific heat | 1.93 | J/kg/℃ | |
| Thermal conductivity coefficient | |||
| — | 1.0 | W/m/K | ASTM E1461 |
| — | 1.3 | W/m/K | ASTM E1461 |
| — | 1.2 | W/m/K | ISO 22007-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+12 | ohms | IEC 60093 |
| Dielectric strength | 27 | kV/mm | IEC 60243-1 |
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 0.75 mm | V-2 | ||
| 1.50 mm | V-0 | ||
| 3.00 mm | V-0 | ||
| Glowing wire flammability index | |||
| 1.0 mm | 960 | ℃ | IEC 60695-2-12 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature – hot air dryer | 80 | °C | |
| Drying time – hot air dryer | 2.0 to 12 | hr | |
| Processing (melt) temperature | 270 to 300 | °C | |
| Mold temperature | > 100 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. through-plane |
| 3. in-plane |
| 4. integral |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |