| About |
|---|
| ALCOM® TCD PA66 5040 14015 is a Polyamide 66 (Nylon 66) product filled with filler. It is available in Asia Pacific, Europe, or North America. Applications of ALCOM® TCD PA66 5040 14015 include electrical/electronic applications, automotive, engineering/industrial parts, housings and lighting applications. Characteristics include: Flame Rated RoHS Compliant Conductive Heat Resistant Insulating&& |
| Product Description | |
|---|---|
| Supplier | ALBIS |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | Thermal conductivity,Heat Stabilized,Insulation,HB |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.41 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| 24 hrs | 0.90 | % | ISO 294-4 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 7500 | MPa | ISO 527-2 |
| tensile strength | |||
| fracture | 60.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 2.0 | % | ISO 527-2 |
| Bending modulus | 7800 | MPa | ISO 178 |
| bending strength | 110 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | 2.0 | kJ/m² | ISO 179-1eA |
| Charpy Unnotch Impact strength | 20 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 205 | ℃ | ISO 75-2/A |
| Vicat Softening Temp | |||
| B50 | 245 | ℃ | ISO 306 |
| Thermal conductivity coefficient | |||
| — | 1.2 | W/m/K | ASTM E1461 |
| — | 3.0 | W/m/K | ASTM E1461 |
| — | 2.0 | W/m/K | ISO 22007-2 |
| Specific heat capacity | 1700 | J/kg/℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+12 | ohms | IEC 60093 |
| Dielectric strength | 54 | kV/mm | IEC 60243-1 |
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50 mm | HB | UL 94 | |
| Glowing wire flammability index | |||
| 2.0 mm | 850 | ℃ | IEC 60695-2-12 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature – hot air dryer | 80 | °C | |
| Drying time – hot air dryer | 2.0 to 12 | hr | |
| Processing (melt) temperature | 300 to 320 | °C | |
| Mold temperature | > 100 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. through-plane |
| 3. in-plane |
| 4. integral |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |