| About |
|---|
| Alcryn® 2150 BK is a Melt Processable Rubber (MPR) product. It is available in Asia Pacific, Europe, or North America. Applications of Alcryn® 2150 BK include hose/tubing, wire & cable, automotive, engineering/industrial parts and handles. Characteristics include: RoHS Compliant WEEE Compliant Chemical Resistant Good Tear Strength High Flow&& |
| Product Description | |
|---|---|
| Supplier | A. Schulman |
| Generic | MPR |
| Material Status | Commercial: Active |
| Features | High Friction,High liquidity,Good tear strength,Good wear resistance,Solvent resistance |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Shore hardness | |||
| Shaw A, 1.90 mm, molded | 49 | ASTM D2240 | |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile permanent deformation | 12 | % | ASTM D412 |
| tensile strength | 6.46 | MPa | ASTM D412 |
| 100% strain | 1.78 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 560 | % | ASTM D412 |
| tear strength | |||
| 24℃ | 29.6 | kN/m | ASTM D624 |
| Compression deformation | |||
| 24℃，22 hr | 21 | % | |
| 100℃，22 hr | 89 | % |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air | |||
| 100℃，1000 hr | 0.0 | % | ASTM D573 |
| The rate of change in tensile modulus in air | |||
| 100℃，1000 hr | 7.6 | % | ASTM D573 |
| The rate of change in ultimate elongation in air | |||
| 100℃，1000 hr | 1.4 | % | ASTM D573 |
| Volume change | |||
| 24 ℃, 168 hr, in reference fuel B | 12 | % | |
| 100 ℃, 168 hr, ASTM standard oil (No.1) | -31 | % | |
| 100 ℃, 168 hr, IRM 903 standard oil (No.3) | 3.0 | % | |
| 100 ℃, 168 hr, in water | 4.0 | % |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -68.9 | ℃ | ASTM D746 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.13 | g/cm³ | ASTM D471 |
| Apparent viscosity of melt | |||
| 190℃，300 sec^-1 | 148 | Pa·s | ASTM D3835 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 3. Type 1 |
| 4. 100% Modulus |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |