| About |
|---|
| ALTECH® PA66 A 2030/109 GF30 GY1176-12LS is a Polyamide 66 (Nylon 66) product filled with 30% glass fiber. It can be processed by injection molding and is available in Asia Pacific, Europe, or North America. Typical application: Housings. Characteristics include: Flame Rated RoHS Compliant Good Mold Release Heat Resistant High Flow&& |
| Product Description | |
|---|---|
| Supplier | ALBIS |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | Good heat aging resistance,High liquidity,Good stripping performance |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.36 | g/cm³ | |
| Water absorption rate | |||
| Saturation, 23 ℃ | 5.0 | % | |
| Equilibrium, 23 ℃, 50% RH | 1.5 | % | |
| Relative viscosity | 3.00 | ||
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 9700 | MPa | |
| tensile strength | |||
| fracture | 160 | MPa | |
| Tensile strain | |||
| fracture | 2.7 | % | |
| Bending modulus | 8500 | MPa | |
| bending strength | 245 | MPa |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | 7.0 | kJ/m² | |
| Charpy Unnotch Impact strength | 50 | kJ/m² |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 250 | ℃ | |
| Vicat Softening Temp | 256 | ℃ | |
| Melting temperature | |||
| DSC | 263 | ℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+12 | ohms | |
| Volume resistivity | 1.0E+17 | ohms·cm | |
| Compared to the leakage tracing index | 525 | V |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 0.75 mm | HB |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature – hot air dryer | 80 | °C | |
| Drying time – hot air dryer | 2.0 to 12 | hr | |
| Recommended maximum moisture content | < 0.15 | % | |
| Processing (melt) temperature | 280 to 300 | °C | |
| Mold temperature | 80 to 120 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. m-Cresol,c = 10 g/l |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |