| About |
|---|
| Altuglas® V920 is a Polymethyl Methacrylate Acrylic product. It can be processed by injection molding or thermoforming and is available in Asia Pacific or Europe. Typical application: Automotive. Characteristics include: Antiblock Lubricated UV Resistant&& |
| Product Description | |
|---|---|
| Supplier | Trinseo |
| Material Status | Commercial: Active |
| Features | High anti-blocking,Weather resistance is good,Lubricating,HB |
| Availabilitys | Europe,Asia Pacific |
| Process Methods | Thermo forming,Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.18 | g/cm³ | ISO 1183-2 |
| Melt Volume Rate | |||
| 230℃，3.8 kg | 7.00 | cm³/10min | ISO 1133 |
| Water absorption rate | ISO 62 2 | ||
| saturated | 1.9 | % | ISO 62-2 |
| balance | 0.30 | % | ISO 62-2 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 3300 | MPa | ISO 527-2 2 |
| tensile strength | |||
| fracture | 69.0 | MPa | ISO 527-2 2 |
| Tensile strain | |||
| fracture | 6.0 | % | ISO 527-2 2 |
| Tensile creep modulus | ISO 899-1 2 | ||
| 1 hr | 2700 | MPa | ISO 899-1 2 |
| 1000 hr | 1800 | MPa | ISO 899-1 2 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 2.00 | kJ/m² | ISO 179/1eA 2 |
| Charpy impact strength | |||
| 23℃ | 20.0 | kJ/m² | ISO 179/1eU 2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ISO 75-2 2 | ||
| 0.45 MPa | 100 | ℃ | ISO 75-2 2 |
| 1.8 MPa | 90.0 | ℃ | ISO 75-2 2 |
| Vicat Softening Temp | |||
| B50 | 101 | ℃ | ISO 306 2 |
| Linear coefficient of thermal expansion | |||
| MD | 7.0E-5 | 1/℃ | ISO 11359-2 2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+14 | ohms | IEC 60093 2 |
| Volume resistivity | 1.0E+15 | ohms·cm | IEC 60093 2 |
| Electrical strength | 20 | kV/mm | IEC 60243-1 2 |
| Relative permittivity | IEC 60250 2 | ||
| 100 Hz | 4.00 | IEC 60250 2 | |
| 1 MHz | 3.00 | IEC 60250 2 | |
| Dissipation factor | IEC 60250 2 | ||
| 100 Hz | 0.050 | IEC 60250 2 | |
| 1 MHz | 0.040 | IEC 60250 2 | |
| Compared to the leakage tracing index | 600 | IEC 60112 2 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.60 mm | HB | ISO 1210 2 |
| Process Conditions | |||
|---|---|---|---|
| Processing temperature | Nominal value | Unit | Test method |
| Preheating temperature | 79 | ℃ | |
| Preheating time | 2-6 | hr | |
| Nozzle temperature | 210 | ℃ | |
| Front cylinder temperature | 216 | ℃ | |
| Middle cylinder temperature | 210 | ℃ | |
| Rear cylinder temperature | 204 | ℃ | |
| Mold temperature | 65 | ℃ | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |