| About |
|---|
| Amodel® HFFR-4133 is a 33% glass-reinforced, halogen-free, flame retardant polyphthalamide (PPA) resin which offers enhanced processing capabilities for electrical and electronic applications. This resin is rated V-0 by Underwriters Laboratories using the UL94 test and is hot-water moldable. It has high flow and a wide processing window and offers good surface appearance, especially for larger electrical components. This grade can withstand the demanding infrared reflow soldering process typically used in the electronics industry. It is well suited for connectors and other electrical devices requiring surface mount technology (SMT). Black: HFFR-4133 BK 324 Natural: HFFR-4133 NT&& |
| Product Description | |
|---|---|
| Supplier | Solvay |
| Generic | PPA |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good flexibility,Good Dimensional Stability,Good Electrical Properties,Quick molding cycle,Halogen free,Flame Characteristics,Solvent resistance,V-0 |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.46 | g/cm³ | ISO 1183/A |
| Shrinkage rate | ISO 294-4 | ||
| TD | 1.3 | % | ISO 294-4 |
| MD | 0.32 | % | ISO 294-4 |
| Water absorption rate | |||
| 24hr | 0.28 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 7.0 to 8.0 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | 40 to 48 | kJ/m² | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 300 | ℃ | ISO 75-2/Af |
| Linear coefficient of thermal expansion | ASTM E831 | ||
| MD：0~90℃ | 2.0E-5 | 1/℃ | ASTM E831 |
| MD：120~200℃ | 1.2E-5 | 1/℃ | ASTM E831 |
| TD：0~90℃ | 8.0E-5 | 1/℃ | ASTM E831 |
| TD：120~200℃ | 1.3E-4 | 1/℃ | ASTM E831 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.3E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | ASTM D149 | ||
| 0.8 mm | 30 | kV/mm | ASTM D149 |
| 1.6 mm | 26 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 100 Hz | 3.78 | ASTM D150 | |
| 1 MHz | 3.53 | ASTM D150 | |
| Dissipation factor | ASTM D150 | ||
| 100 Hz | 5.0E-3 | ASTM D150 | |
| 1 MHz | 0.012 | ASTM D150 | |
| Compared to the leakage tracing index | PLC 0 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 0.40 mm，Black，Natural | V-0 | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 121 | ASTM D785 | |
| Tensile modulus | 12000 | MPa | ISO 527-2 |
| tensile strength | |||
| yield | 145 to 160 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 1.9 to 2.3 | % | ISO 527-2 |
| Bending modulus | 10800 | MPa | ISO 178 |
| bending strength | 220 to 230 | MPa | ISO 178 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 120 | °C | |
| Drying time | 4.0 | hr | |
| Recommended maximum moisture content | 0.030 to 0.060 | % | |
| Barrel rear temperature | 300 | °C | |
| Barrel front temperature | 325 | °C | |
| Processing (melt) temperature | 340 to 350 | °C | |
| Mold temperature | 90 to 110 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Higher values are for NT and BK324. |
| 3. Specimens conditioned for 96 hours at 95°F (35°C) and 90% RH |
| 4. This flammability rating is not intended to reflect hazards presented by this or any other material under actual fire conditions. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |