| About |
|---|
| APICAL 300AV APICAL 300AV is a Thermoset Polyimide material. It is available in North America. Important attributes of APICAL 300AV are: Flame Rated Chemical Resistant Good Dimensional Stability Good Flexibility Typical applications include: Adhesives/Tapes Electrical/Electronic Applications Film Wire & Cable&&APICAL 300AV APICAL 300AV is a PI Film material. It is available in Latin America or North America.&& |
| Product Description | |
|---|---|
| Supplier | Kaneka |
| Generic | PI |
| Material Status | Commercial: Active |
| Features | Good flexibility,Good Dimensional Stability,Solvent resistance,V-0 |
| Availabilitys | North America,Latin America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.42 | g/cm³ | ASTM D1505 |
| Shrinkage rate | |||
| MD | 4.0E-3 | % | ASTM D955 |
| Water absorption rate | |||
| 24hr | 2.9 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| friction coefficient | |||
| With oneself – static | 0.50 | ASTM D1894 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 76 | µm | |
| Secant modulus | |||
| 1% secant, MD | 3170 | MPa | ASTM D882 |
| tensile strength | |||
| MD, fracture | 241 | MPa | ASTM D882 |
| Tensile strain | |||
| MD, fracture | 95 | % | ASTM D882 |
| Elmandorf tear strength | |||
| MD | 24 | g | ASTM D1922 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| specific heat | 1100 | J/kg/℃ | ASTM C351 |
| Relative temperature index | |||
| Electrical performance, 0.075 mm | 240 | ℃ | UL 746 |
| 0.75 mm | 200 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 8.0E+14 | ohms·cm | ASTM D257 |
| Dielectric strength | 180 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 1 kHz | 3.40 | ASTM D150 | |
| Dissipation factor | |||
| 1 kHz | 1.4E-3 | ASTM D150 | |
| Hot wire ignition (HWI) (0.0750 mm) | 120 | sec | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 0.075 mm | V-0 | UL 94 | |
| Extreme oxygen index | 38 | % | ASTM D2863 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 500 V/sec |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |