Appeel® 52004

About
DuPont™ Appeel® 52004 is a modified ethylene acid terpolymer resin designed to function as a sealing layer for lidding applications, most commonly sealing to foamed polystyrene. It is available in pellet form for use in conventional extrusion or coextrusion equipment designed to process polyethylene resins. Uses Lidding Sealant Applications Good heat sealability and easy peelability to foamed PS. Excellent direct foil adhesion without the use of primers. Appeel® 52004 conforms to Code #20 of the Ministry of Health and Welfare Japan. Typical structures for this lidding would be: Paper/PE/Foil/Appeel® 52004 Appeel® 52004 is used as a heat seal layer in lidding material for foamed PS, especially used in the packaging of instant noodle cup. Appeel® 52004 can also be used as a sealant in general flexible packaging. It provides low temperature seals for snacks and confectionery.&&

About

DuPont™ Appeel® 52004 is a modified ethylene acid terpolymer resin designed to function as a sealing layer for lidding applications, most commonly sealing to foamed polystyrene. It is available in pellet form for use in conventional extrusion or coextrusion equipment designed to process polyethylene resins. Uses Lidding Sealant Applications Good heat sealability and easy peelability to foamed PS. Excellent direct foil adhesion without the use of primers. Appeel® 52004 conforms to Code #20 of the Ministry of Health and Welfare Japan. Typical structures for this lidding would be: Paper/PE/Foil/Appeel® 52004 Appeel® 52004 is used as a heat seal layer in lidding material for foamed PS, especially used in the packaging of instant noodle cup. Appeel® 52004 can also be used as a sealant in general flexible packaging. It provides low temperature seals for snacks and confectionery.&&

Product Description
Supplier	DuPont
Generic	EVA
Material Status	Commercial: Active
Features	Good heat sealing,Food contact compliance,Low temperature heat sealing
Availabilitys	Asia Pacific

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.940	g/cm³	ASTM D792
Melt Flow Rate
190℃，2.16kg	32	g/10min	ASTM D1238

THERMAL	Nominal value	Unit	Test method
Vicat Softening Temp	56.0	℃	ASTM D1525
Melting peak temperature	107	℃	ASTM D3418

Supplementary information	Nominal value	Unit	Test method
Maximum Processing Temperature	260	℃

Process Conditions
Extrusion	Nominal value	Unit	Test method
Barrel 1 zone temperature	160	°C
Barrel 2 zone temperature	210	°C
Barrel 3 zone temperature	235	°C
Barrel 4 zone temperature	260	°C
Barrel 5 zone temperature	260	°C
Connector temperature	260	°C
Melt temperature	235 to 260	°C
Nozzle temperature	260	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.