| About |
|---|
| Aristech Acrylics LLC Acrysteel® M is a continuous cast partially cross-linked impact acrylic sheet designed specifically for marine applications. The following physical properties were determined using 0.150″ (3.81 mm) thickness Aristech Acrylics LLC Acrysteel® M acrylic sheet. Properties may vary somewhat for other thicknesses and/or between opaque colors.&& |
| Product Description | |
|---|---|
| Generic | SMMA |
| Material Status | Commercial: Active |
| Features | High impact resistance,Crosslinked |
| Availabilitys | North America |
| Process Methods | Thermo forming |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.18 | g/cm³ | ASTM D792 |
| Shrinkage rate | ASTM D4802 | ||
| MD：3.81 mm | 2.2 | % | ASTM D4802 |
| TD：3.81 mm | 1.9 | % | ASTM D4802 |
| Water absorption rate | |||
| Saturation, 3.81 mm | 0.30 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | |||
| 3.81 mm | 544 | J/m | ASTM D6110 |
| Impact strength of cantilever beam notch | |||
| 3.81mm | 59 | J/m | ASTM D256-A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 3.81 mm | 80.0 | ℃ | ASTM D648 |
| Linear coefficient of thermal expansion | |||
| MD：3.81 mm | 7.2E-5 | 1/℃ | ASTM D696 |
| thermal stability | |||
| 180℃，3.81 mm | No Effect | ASTM D4802 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot forming temperature | |||
| 3.81 mm | 160 to 182 | ℃ | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| M-grade, 3.81 mm | 88 | ASTM D785 | |
| Babbitt hardness | |||
| 3.81 mm | 40 | ASTM D2583 | |
| Tensile modulus | |||
| 3.81 mm | 2870 | MPa | ASTM D638 |
| tensile strength | |||
| Yield, 3.81 mm | 57.0 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 3.81 mm | 14 | % | ASTM D638 |
| Bending modulus | |||
| 3.81 mm | 2730 | MPa | ASTM D790 |
| bending strength | |||
| 3.81 mm | 94.5 | MPa | ASTM D790 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.150 in |
| 3. 30 min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |