| About |
|---|
| Arlon® 3000 XT is a Polyetheretherketone (PEEK) product. It can be processed by injection molding and is available in Europe or North America. Primary characteristic: heat resistant.&& |
| Product Description | |
|---|---|
| Generic | PEEK |
| Material Status | Commercial: Active |
| Features | High Heat Resistance |
| Availabilitys | North America,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.28 | g/cm³ | ASTM D792 |
| Water absorption rate | |||
| 24hr | 0.13 | % | ASTM D570 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | > 300 | ℃ | ASTM D648 |
| Melting temperature | 352 | ℃ | DSC |
| Linear coefficient of thermal expansion | |||
| MD | 4.5E-5 | 1/℃ | ASTM D696 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | |||
| 1.02 mm | 29 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 1.02 mm，1 MHz | 1.96 | ASTM D150 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 90 | ASTM D2240 | |
| Tensile modulus | ASTM D638 | ||
| 24℃ | 3930 | MPa | ASTM D638 |
| 200℃ | 1330 | MPa | ASTM D638 |
| 260℃ | 654 | MPa | ASTM D638 |
| tensile strength | ASTM D638 | ||
| Yield, 24 ℃ | 112 | MPa | ASTM D638 |
| Yield, 200 ℃ | 40.0 | MPa | ASTM D638 |
| Yield, 260 ℃ | 28.3 | MPa | ASTM D638 |
| Fracture, 24 ℃ | 121 | MPa | ASTM D638 |
| Fracture, 200 ℃ | 59.4 | MPa | ASTM D638 |
| Fracture, 260 ℃ | 38.0 | MPa | ASTM D638 |
| Tensile strain | ASTM D638 | ||
| Fracture, 24 ℃ | 15 | % | ASTM D638 |
| Fracture, 200 ℃ | > 25 | % | ASTM D638 |
| Fracture, 260 ℃ | > 25 | % | ASTM D638 |
| Bending modulus | ASTM D790 | ||
| 24℃ | 4410 | MPa | ASTM D790 |
| 200℃ | 1800 | MPa | ASTM D790 |
| 260℃ | 827 | MPa | ASTM D790 |
| bending strength | ASTM D790 | ||
| 5% strain, 24 ℃ | 165 | MPa | ASTM D790 |
| 5% strain, 200 ℃ | 61.0 | MPa | ASTM D790 |
| 5% strain, 260 ℃ | 32.2 | MPa | ASTM D790 |
| Compression modulus | ASTM D695 | ||
| — | 724 | MPa | ASTM D695 |
| — | 1700 | MPa | ASTM D695 |
| — | 3860 | MPa | ASTM D695 |
| compressive strength | ASTM D695 | ||
| 24℃ | 154 | MPa | ASTM D695 |
| 200℃ | 62.7 | MPa | ASTM D695 |
| 260℃ | 34.8 | MPa | ASTM D695 |
| shear strength | ASTM D732 | ||
| 24℃ | 111 | MPa | ASTM D732 |
| 200℃ | 65.2 | MPa | ASTM D732 |
| 260℃ | 48.6 | MPa | ASTM D732 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Type I |
| 3. 500°F |
| 4. 392°F |
| 5. 75°F |
| 6. T |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |