| About |
|---|
| Arlon 45N is a tough, high Tg (175°C by DSC) multifunctional epoxy laminate and prepreg system designed for use in a variety of higher layer count MLB’s. Processeable using conventional FR-4 conditions, 45N is supplied to meet the requirements of IPC-4101/24.&& |
| Product Description | |
|---|---|
| Generic | 环氧树脂 |
| Material Status | Commercial: Active |
| Features | Good flexibility,Good tear strength,Lead content is low to none,V-0 |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.85 | g/cm³ | ASTM D792-A |
| Water absorption rate | |||
| 24hr | 0.10 | % | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 19300 | MPa | Internal Method |
| Poisson’s ratio | 0.20 | ASTM D3039 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| peel strength | Internal Method | ||
| — | 1.4 | kN/m | Internal Method |
| — | 1.4 | kN/m | Internal Method |
| — | 1.4 | kN/m | Internal Method |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Glass transition temperature | 175 | ℃ | Internal Method |
| Linear coefficient of thermal expansion | |||
| MD | |||
| — | 1.4E-5 to 1.6E-5 | cm/cm/℃ | Internal Method |
| < 175℃ | 5.5E-5 | cm/cm/℃ | Internal Method |
| > 175℃ | 2.0E-4 | cm/cm/℃ | Internal Method |
| Thermal conductivity coefficient | |||
| 100℃ | 0.25 | W/m/K | ASTM E1461 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | Internal Method | ||
| — | 4.0E+10 | ohms | Internal Method |
| — | 2.9E+13 | ohms | Internal Method |
| Volume resistivity | Internal Method | ||
| — | 3.3E+13 | ohms·cm | Internal Method |
| — | 2.6E+13 | ohms·cm | Internal Method |
| Dielectric strength | 59 | kV/mm | Internal Method |
| Dielectric constant | |||
| 1 MHz | 4.40 | Internal Method | |
| Dissipation factor | |||
| 1 MHz | 0.025 | Internal Method | |
| Arc resistance | 65.0 | sec | Internal Method |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | V-0 | UL 94 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Expansion rate | |||
| 50 to 260 ℃ | 2.4 | % | Internal Method |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. x and y direction |
| 3. After Thermal Stress |
| 4. After Process Solutions |
| 5. At Elevated Temperatures |
| 6. X-axis |
| 7. Z-axis |
| 8. E24/125 |
| 9. C96/35/90 |
| 10. Range: 402 to 406 |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |