| About |
|---|
| 60 Shore D, Extrusion&& |
| Product Description | |
|---|---|
| Supplier | DSM |
| Generic | TPC-ES |
| Material Status | Commercial: Active |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.27 | g/cm³ | ISO 1183 |
| Melt Volume Rate | |||
| 230℃，2.16 kg | 9.00 | cm³/10min | ISO 1133 |
| Water absorption rate | |||
| Equilibrium, 23 ℃, 50% RH | 0.10 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ISO 868 | ||
| Shore A, 3 seconds | 98 | ISO 868 | |
| Shore A, 15 seconds | 98 | ISO 868 | |
| Shore D, 3 seconds | 61 | ISO 868 | |
| Shore D, 15 seconds | 61 | ISO 868 | |
| Tensile modulus | 310 | MPa | ISO 527-2 |
| tensile strength | ISO 527-2 | ||
| fracture | 33.0 | MPa | ISO 527-2 |
| 5% strain | 15.0 | MPa | ISO 527-2 |
| 10% strain | 20.0 | MPa | ISO 527-2 |
| 50% strain | 23.0 | MPa | ISO 527-2 |
| 100% strain | 21.0 | MPa | ISO 527-2 |
| Nominal tensile fracture strain | 520 | % | ISO 527-2 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30℃ | 5.0 | kJ/m² | ISO 179/1eA |
| 23℃ | No Break | ISO 179/1eA | |
| Impact strength of cantilever beam notch | |||
| -30℃ | 5.0 | kJ/m² | ISO 180-1A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | |||
| A50 | 190 | ℃ | ISO 306/A50 |
| B50 | 90.0 | ℃ | ISO 306 |
| Melting temperature | 208 | ℃ | ISO 11357-3 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 100 | °C | |
| Drying time | 4.0 to 6.0 | hr | |
| Barrel rear temperature | 200 to 220 | °C | |
| Barrel middle temperature | 210 to 230 | °C | |
| Barrel front temperature | 220 to 240 | °C | |
| Nozzle temperature | 230 to 250 | °C | |
| Processing (melt) temperature | 230 to 250 | °C | |
| Mold temperature | 20 to 50 | °C | |
| Injection speed | Moderate-Fast | ||
| Back pressure | 3.00 to 10.0 | MPa | |
| Screw compression ratio | 2.5:1.0 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |