| About |
|---|
| >50% Renewable Content, 3D printing grade&& |
| Product Description | |
|---|---|
| Supplier | DSM |
| Generic | TPE |
| Material Status | Commercial: Active |
| Features | Renewable resources,HB |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.24 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 240℃，2.16kg | 75 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD | 0.50 to 0.60 | % | ASTM D955 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ASTM D256 | ||
| -40℃ | 无断裂 | ||
| 23℃ | 无断裂 | ||
| Dart impact equipped with measuring instruments | 36.2 | J | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | 193 | ℃ | ASTM D1525 3 |
| Melting temperature | 204 | ℃ |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.60 mm | HB | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 50 | ASTM D2240 | |
| tensile strength | ASTM D638 | ||
| Fracture, -40 ℃ | 48.3 | MPa | |
| Fracture, 23 ℃ | 48.3 | MPa | |
| Tensile strain | ASTM D638 | ||
| Fracture, -40 ℃ | 900 | % | |
| Fracture, 23 ℃ | 900 | % |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 76.7 to 82.2 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Barrel rear temperature | 177 to 182 | °C | |
| Barrel middle temperature | 188 to 193 | °C | |
| Barrel front temperature | 193 to 199 | °C | |
| Nozzle temperature | 202 to 210 | °C | |
| Processing (melt) temperature | 193 to 216 | °C | |
| Mold temperature | 21.1 to 32.2 | °C | |
| Injection pressure | 110 to 138 | MPa | |
| Injection speed | 中等 | ||
| Hold pressure | 68.9 to 89.6 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Tensile Bar 45°-45° |
| 3. Tensile bar 45°-45° |
| 4. Tensile bar 0°-90° |
| 5. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |