| About |
|---|
| AVALON 90 AKU is a UV-stabilised, high performance, thermoplastic polyurethane-based material for injection moulding. AVALON 90 AKU is part of the AVALON Crystal Range and offers a specially designed, flexible material with a higher degree of transparency compared with conventional TPU at the same hardness. AVALON Crystal materials are particularly suitable for the sporting goods and fashion markets and are supplied with a high level of stabilisation against premature yellowing from sunlight. The features offered include: UV resistance Transparency Durability phthalate free TPU&& |
| Product Description | |
|---|---|
| Supplier | Huntsman |
| Generic | TPU |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Good flexibility,Durability |
| Availabilitys | North America,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.21 | g/cm³ | ISO 2781 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ISO 37 | ||
| fracture | 45.0 | MPa | ISO 37 |
| 100% strain | 8.00 | MPa | ISO 37 |
| 300% strain | 16.0 | MPa | ISO 37 |
| Tensile strain | |||
| fracture | 450 | % | ISO 37 |
| tear strength | 110 | kN/m | ISO 34-1 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ISO 868 | ||
| Shaw’s A | 90 | ISO 868 | |
| Shaw’s D | 44 | ISO 868 | |
| Ross Twist Test | |||
| -10℃ | > 5.0E+4 | Cycles | |
| 23℃ | > 5.0E+4 | Cycles | |
| abrasion resistance | 50.0 | mm³ | ISO 4649 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature – hot air dryer | 80 to 90 | °C | |
| Drying time – hot air dryer | 2.0 | hr | |
| Hopper temperature | 25 to 35 | °C | |
| Barrel rear temperature | 195 to 205 | °C | |
| Barrel middle temperature | 205 to 215 | °C | |
| Barrel front temperature | 210 to 220 | °C | |
| Nozzle temperature | 205 to 215 | °C | |
| Mold temperature | 25 to 50 | °C | |
| Injection pressure | 2.00 to 10.0 | MPa | |
| Injection speed | 慢 | ||
| Hold pressure | 1.00 to 5.00 | MPa | |
| Back pressure | 0.0300 to 0.300 | MPa | |
| Screw speed | 20 to 80 | rpm | |
| Screw length to diameter ratio | 20.0:1.0 to 25.0:1.0 | ||
| Screw compression ratio | 2.0 : 1.0 to 3.0 : 1.0 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. BS 5131 |
| 3. Method Ba, Angle (Unnicked) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |