AXELERON™ CX 6944 NT CPD

About
AXELERON™ CX 6944 NT CPD is a high density polyethylene compound (“CPD”) designed for gas-injected foam insulation for CATV cable. This high density polyethylene compound has excellent electrical properties and toughness, as well as the needed stabilization for these applications. AXELERON™ CX 6944 NT CPD is commonly used in combination with AXELERON™ CX 1253 NT CPD LDPE. To obtain optimal cellular structure, an additional 0.1% to 0.3% of a suitable nucleating agent is recommended such as those in AXELERON™ CX A-0012 NT CPD and AXELERON™ CX 0078 NT CPD masterbatches. Specifications Dow AXELERON™ CX 6944 NT CPD meets the following raw material specification: ASTM D 1248 Type IV, Class A, Category 3 Wire insulated with Dow AXELERON™ CX 6944 NT CPD, using sound commercial extrusion practices, should meet the requirements of: Telecordia GR-1398-CORE Telecordia GR-1399-CORE&&

About

AXELERON™ CX 6944 NT CPD is a high density polyethylene compound (“CPD”) designed for gas-injected foam insulation for CATV cable. This high density polyethylene compound has excellent electrical properties and toughness, as well as the needed stabilization for these applications. AXELERON™ CX 6944 NT CPD is commonly used in combination with AXELERON™ CX 1253 NT CPD LDPE. To obtain optimal cellular structure, an additional 0.1% to 0.3% of a suitable nucleating agent is recommended such as those in AXELERON™ CX A-0012 NT CPD and AXELERON™ CX 0078 NT CPD masterbatches. Specifications Dow AXELERON™ CX 6944 NT CPD meets the following raw material specification: ASTM D 1248 Type IV, Class A, Category 3 Wire insulated with Dow AXELERON™ CX 6944 NT CPD, using sound commercial extrusion practices, should meet the requirements of: Telecordia GR-1398-CORE Telecordia GR-1399-CORE&&

Product Description
Supplier	DOW
Generic	HDPE
Material Status	Commercial: Active
Availabilitys	North America,Latin America
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.965	g/cm³	ASTM D792
Melt Flow Rate
190℃，2.16kg	8.0	g/10min	ASTM D1238

MECHANICAL	Nominal value	Unit	Test method
tensile strength	33.1	MPa	ASTM D638
Tensile strain
fracture	650	%	ASTM D638

THERMAL	Nominal value	Unit	Test method
Embrittlement temperature	< -100	℃	ASTM D746

Electrical performance	Nominal value	Test method
Dielectric constant
1 MHz	2.34	ASTM D1531
Dissipation factor
1 MHz	4.0E-5	ASTM D1531

Process Conditions
Extrusion	Nominal value	Unit	Test method
Melt temperature	160 to 179	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.