AXELERON™ GP D-0588 BK CPD

About
AXELERON™ GP D-0588 BK CPD, with a density of 0.93, and a melt index of 0.2, is a prime quality telephone telecom cable black jacketing compound (“CPD”). It offers excellent environmental stress cracking resistance, outdoor weatherability, toughness, low temperature performance, and extrudability. AXELERON™ GP D-0588 BK CPD can be used by wire and cable manufacturers for the entire range of telephone telecom cable sizes and configurations. It is suitable for both aircore and jelly-filled construction, and in both aerial and buried applications. Specifications AXELERON™ GP D-0588 BK CPD meets the following raw material specifications: ASTM D 1248 IC-5 Grades, E5, J1 J3 ISO 1872-1-PE, KCHL, 23-D003 Federal LP-390 C, III-L, Grades 2,3, and 4, Category 5 REA PE-22, 38, 39, 86, 89, 90 Cable jacketed with AXELERON™ GP D-0588 BK CPD using sound commercial extrusion practices, should meet the following specifications: ICEA: S-61-402; NEMA WC 5 ANSI: C8. 35 ASTM: D 2308 British Telecommunications plc M132 Telcordia GR 421 Core ANSI/ICEA S-84-608-1988 EN 50290-2-24, grade LD IEC 60708 BS 6234: Type 03C, TS1&&

About

AXELERON™ GP D-0588 BK CPD, with a density of 0.93, and a melt index of 0.2, is a prime quality telephone telecom cable black jacketing compound (“CPD”). It offers excellent environmental stress cracking resistance, outdoor weatherability, toughness, low temperature performance, and extrudability. AXELERON™ GP D-0588 BK CPD can be used by wire and cable manufacturers for the entire range of telephone telecom cable sizes and configurations. It is suitable for both aircore and jelly-filled construction, and in both aerial and buried applications. Specifications AXELERON™ GP D-0588 BK CPD meets the following raw material specifications: ASTM D 1248 IC-5 Grades, E5, J1 J3 ISO 1872-1-PE, KCHL, 23-D003 Federal LP-390 C, III-L, Grades 2,3, and 4, Category 5 REA PE-22, 38, 39, 86, 89, 90 Cable jacketed with AXELERON™ GP D-0588 BK CPD using sound commercial extrusion practices, should meet the following specifications: ICEA: S-61-402; NEMA WC 5 ANSI: C8. 35 ASTM: D 2308 British Telecommunications plc M132 Telcordia GR 421 Core ANSI/ICEA S-84-608-1988 EN 50290-2-24, grade LD IEC 60708 BS 6234: Type 03C, TS1&&

Product Description
Supplier	DOW
Generic	LDPE
Material Status	Commercial: Active
Availabilitys	Africa & Middle East ,North America,Asia Pacific

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.931	g/cm³	ASTM D1505
Melt Flow Rate
190℃，2.16kg	0.21	g/10min	ASTM D1238
ESCR(Environmental Stress Cracking Resistance)
10% non-ionic detergent, F0	> 2000	hr	IEC 60811-4-1/B
100% non-ionic detergent, F20	> 500	hr	ASTM D1693
Carbon black content	2.6	%	ASTM D1603
absorption coefficient
kAB/m	> 400		ASTM D3349

THERMAL	Nominal value	Unit	Test method
Embrittlement temperature	< -90.0	℃	ASTM D746
Oxygen sensing time			ISO 11357-6
200℃	74	min	ISO 11357-6
210℃	30	min	ISO 11357-6

Electrical performance	Nominal value	Test method
Dielectric constant
1 Hz	2.48	ASTM D1531
Dissipation factor
1 MHz	3.0E-4	ASTM D1531

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shore D, 15 seconds	50		ISO 868
tensile strength			ASTM D638
yield	9.31	MPa	ASTM D638
—	17.6	MPa	ASTM D638
Tensile strain
fracture	800	%	ASTM D638

Process Conditions
Extrusion	Nominal value	Unit	Test method
Melt temperature	204 to 227	°C

Notes
1. Typical properties: these are not to be construed as specifications.
2. Without oven conditioning.
3. Type IV, 2.0 in/min
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.