| About |
|---|
| Product Description | |
|---|---|
| Supplier | Covestro |
| Generic | PC+ABS |
| Material Status | Commercial: Active |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Water absorption rate | |||
| 0.7 | % | ISO 62 | |
| 23℃，50% RH | 0.2 | % | ISO 62 |
| Spiral flow length | |||
| 260℃，2×8.7mm | 450 | mm | |
| Density | 1.1 | g/cm³ | ISO 1183 |
| Melt Volume Rate | |||
| 260℃ | 12 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| TD：500 bar | 0.55-0.70 | % | ISO 2577 |
| MD：500 bar | 0.55-0.70 | % | ISO 2577 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| 50 mm/min | 40 | MPa | ISO 527 |
| Tensile modulus | |||
| 1 mm/min | 2100 | MPa | ISO 527 |
| Tensile stress | |||
| yield | 49 | MPa | ISO 527 |
| Tensile strain | |||
| yield | 3.7 | % | ISO 527 |
| fracture | > 50 | % | ISO 527 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Notched impact strength of cantilever beam | N | kJ/m² | ISO 180-1U |
| -30℃ | N | kJ/m² | ISO 180-1U |
| 23℃ | |||
| Impact strength of cantilever beam notch | |||
| -30℃ | 36 | kJ/m² | ISO 180-1A |
| 23℃ | 40 | kJ/m² | ISO 180-1A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa | 95 | ℃ | ISO 75 |
| 0.45 MPa | 112 | ℃ | ISO 75 |
| Vicat Softening Temp | |||
| B50 | 110 | ℃ | ISO 306 |
| Linear coefficient of thermal expansion | |||
| MD：23~55℃ | 0.85 | ×10-4/K | ISO E831 |
| TD：23~55°C | 0.90 | ×10-4/K | ISO E831 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | 35 | KV/mm | IEC 243-1 |
| Relative permittivity | |||
| 1 MHz | 3.0 | IEC 250 | |
| 100 Hz | 3.1 | IEC 250 | |
| Dissipation factor | |||
| 1 MHz | 85 | 0.0001 | IEC 250 |
| 100 Hz | 35 | 0.0001 | IEC 250 |
| tracking resistance | |||
| Solution A | 275 | 等级 | IEC 112 |
| Surface resistivity | 1.0E+16 | ohms | IEC 93 |
| Volume resistivity | 1.0E+17 | ohms·cm | IEC 93 |
| Process Conditions | |||
|---|---|---|---|
| Melt Temperature | Nominal value | Unit | Test method |
| Mold temperature | Nominal value | Unit | Test method |
| Injection speed | Nominal value | Unit | Test method |
| 260 | ℃ | ISO 294 | |
| 80 | ℃ | ISO 294 | |
| 240 | mm/s | ISO 294 | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |