| About |
|---|
| The Bayflex 110-50 system produces a solid urethane elastomer which has a flexural modulus of approximately 50,000 psi* at room temperature. This system can be used with or without milled glass fiber or mineral reinforcements. The Bayflex 110-50 system is used in applications requiring excellent impact properties such as automotive fascias, agricultural and construction equipment, specialty vehicles and recreational equipment. The Bayflex 110-50 system is a formulated elastomeric reaction injection molding (RIM) system supplied as two liquid components. Component A is a diphenylmethane diisocyanate (MDI) prepolymer, and Component B is a polyether polyol system. As with any product, use of the Bayflex 110-50 system in a given application must be tested (including field testing, etc.) in advance by the user to determine suitability.&& |
| Product Description | |
|---|---|
| Supplier | Covestro |
| Generic | PUR-脂肪族+MDI |
| Material Status | Commercial: Active |
| Features | High impact resistance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | |||
| — | 1.19 | g/cm³ | ASTM D792 |
| — | 1.20 | g/cm³ | ASTM D1622 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.47 | % | Internal Method |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| Fracture, 3.18 mm | 20.0 | MPa | ASTM D412 |
| Tensile strain | |||
| Fracture, 3.18 mm | 95 | % | ASTM D412 |
| tear strength | |||
| 3.18 mm | 96.3 | kN/m | ASTM D624 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 3.2mm | 260 | J/m | ASTM D256 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Heat Sag | ASTM D3769 | ||
| 4 in Overhang：121℃，3.18 mm | 7.11 | mm | ASTM D3769 |
| 6 in Overhang：121℃，3.18 mm | 12.7 | mm | ASTM D3769 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw D, 3.18 mm | 64 | ASTM D2240 | |
| Bending modulus | ASTM D790 | ||
| -30℃，3.18 mm | 1380 | MPa | ASTM D790 |
| 23℃，3.18 mm | 931 | MPa | ASTM D790 |
| 65℃，3.18 mm | 552 | MPa | ASTM D790 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Linear coefficient of thermal expansion | |||
| MD：3.2 mm | 7.2E-5 | 1/℃ | ASTM D696 |
| Thermosetting components | |||
| Component A | 按重量计算的混合比: 58 | ||
| Component B | 按重量计算的混合比: 100 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 3. 105 Index |
| 4. 1 hr |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |