Biograde B-M - SOLIAO

About
A fully biodegradable resin for rigid moulding applications Greater than 98% biodegradability when tested to ISO14855 Can be used for injection moulding and profile extrusion BIOGRADE B-M is a fully biodegradable plastic based on a blend of thermoplastic starch (TPS), aliphatic polyesters (AP) and natural plasticizers (glycerol and sorbitol). This grade of resin is compatibilised to offer a high level of mechanical strength, good elongation properties and toughness. The resin is based on corn starch which is a renewable material. The resin does not contain polyolefins. Applications Biodegradable injection moulded products such as cutlery, toothbrushes, combs, shavers, golf-tees, plant markers, etc. Extruded tubes and rods Biodegradable stakes and pegs Biodegradable tags Extruded pipes Injection moulded caps and closures Compostable rigid products if wall thickness is kept below 1 mm.&&

About

A fully biodegradable resin for rigid moulding applications Greater than 98% biodegradability when tested to ISO14855 Can be used for injection moulding and profile extrusion BIOGRADE B-M is a fully biodegradable plastic based on a blend of thermoplastic starch (TPS), aliphatic polyesters (AP) and natural plasticizers (glycerol and sorbitol). This grade of resin is compatibilised to offer a high level of mechanical strength, good elongation properties and toughness. The resin is based on corn starch which is a renewable material. The resin does not contain polyolefins. Applications Biodegradable injection moulded products such as cutlery, toothbrushes, combs, shavers, golf-tees, plant markers, etc. Extruded tubes and rods Biodegradable stakes and pegs Biodegradable tags Extruded pipes Injection moulded caps and closures Compostable rigid products if wall thickness is kept below 1 mm.&&

Product Description
Generic	生物可降解聚合物
Material Status	Commercial: Active
Features	Good Rigidity,Good flexibility,Renewable resources,Biodegradable,Good Tensile Strength
Availabilitys	Asia Pacific
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.22	g/cm³	ASTM D4883
Melt Flow Rate
150℃，0.325kg	1.8	g/10min	ASTM D1238

MECHANICAL	Nominal value	Unit	Test method
tensile strength
fracture	19.5	MPa	ASTM D883
Tensile strain
fracture	1.9	%	ASTM D883

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch	24	J/m	ASTM D256
Notched impact strength of cantilever beam	160	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Melting peak temperature	70.0 to 80.0	℃	ASTM D3418

Process Conditions
injection	Nominal value	Unit	Test method
Extrusion	Nominal value	Unit	Test method
Recommended maximum moisture content	0.20	%
Barrel middle temperature	150 to 160	°C
Barrel front temperature	130 to 140	°C
Nozzle temperature	140 to 160	°C
Processing (melt) temperature	160 to 165	°C
Mold temperature	10 to 15	°C
Recommended maximum moisture content	0.20	%
Melt temperature	160 to 165	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.