| About |
|---|
| Bormed HD800CF is a polypropylene homopolymer The current version of Bormed HD800CF has been scheduled for deletion. Please refer to Bormed HD800CF-11 documentation for new projects. In case of questions, please contact either your responsible Borealis Sales Manager and/or Application Development Engineer. This grade is suitable for the manufacturing of non-oriented cast films on chill roll process and blown films on tubular water quenching process. This grade can also be processed using injection moulding technology. CAS-No.: 9003-07-0 Applications Bormed HD800CF has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed HD800CF . Medical device packaging Parenteral nutrition bags Closures Pouches for IV solutions Pouches for Continuous Ambulatory Peritoneal Dialysis Secondary packaging This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special features High gloss Sterilisability by means of water steam Low haze High stiffness Very good heat deformation resistance High water vapour barrier&& |
| Product Description | |
|---|---|
| Supplier | Borealis AG |
| Generic | PP homopolymerization |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good surface appearance,Steam sterilized,High Heat Resistance,Moisture resistance,Low density,Homopolymer |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.905 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 8.0 | g/10min | ISO 1133 |
| molecular weight distribution | Medium | ||
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Bending modulus | |||
| 20 ℃, injection molding | 1400 | MPa | ISO 178 |
| friction coefficient | > 0.70 | ISO 8295 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | ISO 527-3 | ||
| MD，50 µm | 800 | MPa | ISO 527-3 |
| TD，50 µm | 800 | MPa | ISO 527-3 |
| tensile strength | ISO 527-3 | ||
| MD，50 µm | 45.0 | MPa | ISO 527-3 |
| TD，50 µm | 40.0 | MPa | ISO 527-3 |
| Tensile strain | ISO 527-3 | ||
| MD, fracture, 50 µ m | 600 | % | ISO 527-3 |
| TD, fracture, 50 µ m | 650 | % | ISO 527-3 |
| Instrumented Puncture Test（50.0 µm） | 100 | J/cm | ISO 7765-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | 164 | ℃ | ISO 11357-3 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 20°，50 µm | > 110 | ASTM D2457 | |
| Haze | |||
| 50 µm | < 2.0 | % | ASTM D1003 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Cast Film |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |