| About |
|---|
| Bormed HD810MO is a resin intended for evaluation for use in Healthcare applications. Bormed HD810MO is a nucleated polypropylene homopolymer with a medium melt flow rate. Bormed HD810MO is specially formulated for production of articles which need to be sterilized with radiation (gamma and beta radiation). Tests on specimen radiated at 25 kGy have shown stability for 5 years when stored at room temperature. Material can also well be sterilised with ethylene oxide or steam. Applications Bormed HD810MO has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed HD810MO . Disposable non pre-filled syringes Catheter Blood collection systems Laboratory disposable This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special features Radiation resistance High transparency&& |
| Product Description | |
|---|---|
| Supplier | Borealis AG |
| Generic | PP homopolymerization |
| Material Status | Commercial: Active |
| Features | Excellent Processability,Good Clarity,Renewable resources,Good liquidity,Good Printability,Gamma radiation,Radiation disinfection,Solvent resistance,Homopolymer |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.907 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 10 | g/10min | ISO 1133 |
| Shrinkage rate | 1.0 to 2.0 | % | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 4.5 | kJ/m² | ISO 179/1eA |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 90.0 | ℃ | ISO 75-2/B |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 1100 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 29.5 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| yield | 13 | % | ISO 527-2/50 |
| Rockwell hardness | |||
| R-level | 94 | ISO 2039-2 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Processing (melt) temperature | 220 to 260 | °C | |
| Mold temperature | 30 to 40 | °C | |
| Injection speed | Moderate-Fast | ||
| Hold pressure | 20.0 to 50.0 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Injection molded specimen |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |