Bormed™ HE9621PH3-01

About
Bormed HE9621PH3-01 is a resin intended for evaluation for use in Healthcare applications. HE9621PH3-01 is a high density polyethylene with narrow molecular weight distribution typically used in injection moulding of articles requiring medium flow with high rigidity. This grade is designed for articles which require high stiffness and low warpage. Material can be sterilised with ethylene oxide, steam and radiation up to 35 kGy; as a result of sterilisation by radiation some minor yellowing can occur. CAS-No.: 9002-88-4 Applications Bormed HE9621PH3-01 has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed HE9621PH3-01 . Plungers for syringes Packaging for powder, tablets & pills Caps and closures This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special Features High rigidity Low extractables&&

About

Bormed HE9621PH3-01 is a resin intended for evaluation for use in Healthcare applications. HE9621PH3-01 is a high density polyethylene with narrow molecular weight distribution typically used in injection moulding of articles requiring medium flow with high rigidity. This grade is designed for articles which require high stiffness and low warpage. Material can be sterilised with ethylene oxide, steam and radiation up to 35 kGy; as a result of sterilisation by radiation some minor yellowing can occur. CAS-No.: 9002-88-4 Applications Bormed HE9621PH3-01 has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed HE9621PH3-01 . Plungers for syringes Packaging for powder, tablets & pills Caps and closures This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special Features High rigidity Low extractables&&

Product Description
Supplier	Borealis AG
Generic	HDPE
Material Status	Commercial: Active
Features	Good Rigidity,Low warping,Low extract,Steam sterilized,Renewable resources,Weight distribution,Radiation disinfection,Moderate liquidity,Ethylene oxide disinfection
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.964	g/cm³	ISO 1183
Melt Flow Rate
190℃，2.16kg	12	g/10min	ISO 1133

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength	4.0	kJ/m²	ISO 179-1eA

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	79.0	℃	ISO 75-2/B

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D	62		ISO 868
Tensile modulus
injection molding	1150	MPa	ISO 527-1-2
tensile strength
Yield, injection molding	26.0	MPa	ISO 527-2/50
Tensile strain
Yield, injection molding	9.0	%	ISO 527-2/50
Bending modulus	1300	MPa	ISO 178

Process Conditions
injection	Nominal value	Unit	Test method
Processing (melt) temperature	200 to 260	°C
Mold temperature	10 to 40	°C
Injection speed	快速

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.