Bormed™ LE6609-PH

About
Bormed LE6609-PH is a resin intended for evaluation for use in Healthcare applications. Bormed LE6609-PH is an additive free low density polyethylene typically used in blow moulding articles . Material is characterised with a balanced inflexibility to facilitate to collapsibility of containers. Bottles and ampoules made from Bormed LE6609PH can be steam sterilised at temperatures above 110 °C. Products made from Bormed LE6609-PH can be sterilised by using ethylene oxide or radiation up to 35 kGy. Applications Bormed LE6609-PH has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed LE6609-PH . Bottles for irrigation solutions Ampoules for injectable solutions Bottles for IV-solutions This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special features No additives&&

About

Bormed LE6609-PH is a resin intended for evaluation for use in Healthcare applications. Bormed LE6609-PH is an additive free low density polyethylene typically used in blow moulding articles . Material is characterised with a balanced inflexibility to facilitate to collapsibility of containers. Bottles and ampoules made from Bormed LE6609PH can be steam sterilised at temperatures above 110 °C. Products made from Bormed LE6609-PH can be sterilised by using ethylene oxide or radiation up to 35 kGy. Applications Bormed LE6609-PH has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed LE6609-PH . Bottles for irrigation solutions Ampoules for injectable solutions Bottles for IV-solutions This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special features No additives&&

Product Description
Supplier	Borealis AG
Generic	LDPE
Material Status	Commercial: Active
Features	Good flexibility,Steam sterilized,Renewable resources,Gamma radiation,E-beam disinfection,Low density,Radiation disinfection,Soft
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.930	g/cm³	ISO 1183
Melt Flow Rate
190℃，5.0kg	0.30	g/10min	ISO 1133

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D, injection molding	53		ISO 868
Tensile modulus
injection molding	350	MPa	ISO 527-1-2
tensile strength
Yield, injection molding	14.0	MPa	ISO 527-2/50

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	54.0	℃	ISO 75-2/B

Process Conditions
Extrusion	Nominal value	Unit	Test method
Melt temperature	165 to 200	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.