Braskem PE LHB-118/21AF

About
LHB118/21 AF is a LLDPE copolymer produced by Braskem. It is a ready-to-use product since it contains 10% LDPE. Its additive package was optimized to avoid blocking, even at low thickness. Film obtained from this grade show very good mechanical properties and a good balance between sealability and processability. Very low gel amount. Additive: Processing Aid Medium Antioxidants Medium Slip Medium Antiblocking High Applications: Frozen bags; general purpose. Process: Blown Film Extrusion&&

About

LHB118/21 AF is a LLDPE copolymer produced by Braskem. It is a ready-to-use product since it contains 10% LDPE. Its additive package was optimized to avoid blocking, even at low thickness. Film obtained from this grade show very good mechanical properties and a good balance between sealability and processability. Very low gel amount. Additive: Processing Aid Medium Antioxidants Medium Slip Medium Antiblocking High Applications: Frozen bags; general purpose. Process: Blown Film Extrusion&&

Product Description
Supplier	Braskem
Generic	Linear low density polyethylene
Material Status	Commercial: Active
Features	Excellent Processability,High anti-blocking,Low speed solidification point,Food contact compliance,Inoxidizability,Low density,Copolymer
Availabilitys	Latin America,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.918	g/cm³	ASTM D792
Melt Flow Rate
190℃，2.16kg	1.0	g/10min	ASTM D1238

film	Nominal value	Unit	Test method
tensile strength
TD, fracture, 38 µ m, blow molded film	30.0	MPa	ASTM D882
MD, fracture, 38 µ m, blow molded film	40.0	MPa	ASTM D882
Tensile strain
TD, fracture, 38 µ m, blow molded film	1300	%	ASTM D882
MD, fracture, 38 µ m, blow molded film	1000	%	ASTM D882
Bending modulus
1% secant, TD, 38 µ m, blow molded film	210	MPa	ASTM D790
1% secant, MD, 38 µ m, blow molded film	180	MPa	ASTM D790
Drop hammer impact
38 µ m, blow molded film	100	g	ASTM D1709
tear strength
MD, 38 µ m, blow molded film	80	g	ASTM D1922
Elmandorf tear strength
TD, 38 µ m, blow molded film	560	g	ASTM D1922

optical performance	Nominal value	Unit	Test method
gloss
60 °, 38.0 µ m, blow molded film	98		ASTM D2457
Haze
38 µ m, blow molded film	12	%	ASTM D1003

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.