| About |
|---|
| LL5405S is a Linear Low Density Polyethylene (LLDPE) developed for blown film extrusion. Films obtained with this product show a good processing performance balanced with good mechanical properties as well as processability. Very low gel amount. Additive: Antiblocking High Slip – High Applications: LLDPE and HDPE blends, films with low thickness for general use, bags for waste, special bags for water and protection of clothes. Process: Blown film extrusion.&& |
| Product Description | |
|---|---|
| Supplier | Braskem |
| Generic | Linear low density polyethylene |
| Material Status | Commercial: Negative |
| Features | Excellent Processability,Smoothness,High anti-blocking,Low speed solidification point |
| Availabilitys | Latin America,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.919 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 1.0 | g/10min | ASTM D1238 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| friction coefficient | |||
| Blown film | 0.10 | ASTM D1894 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ASTM D882 | ||
| MD, fracture, 40 µ m, blow molded film | 35.0 | MPa | ASTM D882 |
| TD, fracture, 40 µ m, blow molded film | 25.0 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD, fracture, 40 µ m, blow molded film | 1000 | % | ASTM D882 |
| TD, fracture, 40 µ m, blow molded film | 1200 | % | ASTM D882 |
| Bending modulus | ASTM D790 | ||
| 1% secant, MD, 40 µ m, blow molded film | 160 | MPa | ASTM D790 |
| 1% secant, TD, 40 µ m, blow molded film | 180 | MPa | ASTM D790 |
| Drop hammer impact | |||
| 40 µ m, blow molded film | 120 | g | ASTM D1709 |
| Elmandorf tear strength | ASTM D1922 | ||
| MD: 40 µ m, blow molded film | 90 | g | ASTM D1922 |
| TD: 40 µ m, blow molded film | 900 | g | ASTM D1922 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | ASTM D2457 | ||
| 45 °, 40.0 µ m, blow molded film | 55 | ASTM D2457 | |
| 60 °, 40.0 µ m, blow molded film | 80 | ASTM D2457 | |
| Haze | |||
| 40 µ m, blow molded film | 18 | % | ASTM D1003 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Blocking force | |||
| 40.0 µm | 8.00 | g/100 cm² | ASTM D3354 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Blown Film |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |