Bynel® 41E687

About
BYNEL® Series 4100 series resins are anhydride-modified, linear low-density polyethylene (LLDPE) resins. All BYNEL Series 4100 series resins are available in pellet form for use in conventional extrusion and coextrusion equipment designed to process polyethylene resins. BYNEL 4100 series resins adhere to a variety of materials. They are most often used to adhere to EVOH, polyamide, PE and ethylene copolymers. Series 4100 resins can be used in coextrusion processes including: blown film cast film/sheet blow molding melt and solid phase thermoforming sheet and tubing LLDPE resins are known for their temperature resistance, clarity and toughness. These physical properties make the 4100 series resins work well in applications such as: boil-in-bag structures blow molded containers in which drop strength is important bag-in-box films film where LLDPE is the heat seal layer.&&

About

BYNEL® Series 4100 series resins are anhydride-modified, linear low-density polyethylene (LLDPE) resins. All BYNEL Series 4100 series resins are available in pellet form for use in conventional extrusion and coextrusion equipment designed to process polyethylene resins. BYNEL 4100 series resins adhere to a variety of materials. They are most often used to adhere to EVOH, polyamide, PE and ethylene copolymers. Series 4100 resins can be used in coextrusion processes including: blown film cast film/sheet blow molding melt and solid phase thermoforming sheet and tubing LLDPE resins are known for their temperature resistance, clarity and toughness. These physical properties make the 4100 series resins work well in applications such as: boil-in-bag structures blow molded containers in which drop strength is important bag-in-box films film where LLDPE is the heat seal layer.&&

Product Description
Supplier	DuPont
Generic	Linear low density polyethylene
Material Status	Commercial: Active
Features	Good bond
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.910	g/cm³	ASTM D792
Density	0.910	g/cm³	ISO 1183
Melt Flow Rate
190℃，2.16kg	1.7	g/10min	ASTM D1238
190℃，2.16kg	1.7	g/10min	ISO 1133

THERMAL	Nominal value	Unit	Test method
Vicat Softening Temp	84.0	℃	ASTM D1525
Vicat Softening Temp	84.0	℃	ISO 306
Melting peak temperature	119	℃	ASTM D3418
Melting temperature
DSC	119	℃	ISO 3146
freezing point	103	℃	ASTM D3418

Process Conditions
Extrusion	Nominal value	Unit	Test method
Barrel 1 zone temperature	160	°C
Barrel 2 zone temperature	185	°C
Barrel 3 zone temperature	235	°C
Barrel 4 zone temperature	235	°C
Barrel 5 zone temperature	235	°C
Connector temperature	235	°C
Melt temperature	< 260	°C
Nozzle temperature	235	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.