CABELEC® CA3178

About
CABELEC CA3178 electrically conductive compound is made from conductive carbon black dispersed in polyamide 6. Its electrical and mechanical properties are not impacted by normal atmospheric conditions. It has been developed for injection moulding applications. Applications CABELEC CA3178 conductive compound is suitable for use in products for packaging and handling of electronic products where it is desirable to mitigate the hazard of electrostatic discharge. Typical areas of application are explosives, electronic components and pigments.&&

About

CABELEC CA3178 electrically conductive compound is made from conductive carbon black dispersed in polyamide 6. Its electrical and mechanical properties are not impacted by normal atmospheric conditions. It has been developed for injection moulding applications. Applications CABELEC CA3178 conductive compound is suitable for use in products for packaging and handling of electronic products where it is desirable to mitigate the hazard of electrostatic discharge. Typical areas of application are explosives, electronic components and pigments.&&

Product Description
Generic	PA6
Material Status	Commercial: Active
Features	Conductive,HB
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.20	g/cm³	Internal Method
Melt Flow Rate
275℃，10.0kg	10	g/10min	ISO 1133
Shrinkage rate
MD	1.5 to 2.0	%	ASTM D955

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shore D, 15 seconds	78		ASTM D2240
tensile strength
fracture	45.0	MPa	ISO 527-2
yield	55.0	MPa	ISO 527-2
Tensile strain
fracture	15	%	ISO 527-2
Bending modulus	2700	MPa	ISO 178
bending strength	89.0	MPa	ISO 178

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength			ISO 179
-30℃	7.0	kJ/m²	ISO 179
23℃	12	kJ/m²	ISO 179
Impact strength of cantilever beam notch
23℃	15	kJ/m²	ISO 180

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
1.8 MPa, unannealed	66.0	℃	ISO 75-2/A
Vicat Softening Temp	215	℃	ISO 306/A

Electrical performance	Nominal value	Unit	Test method
Surface resistivity	1.0E+3	ohms	Internal Method
Volume resistivity	1.0E+2	ohms·cm	Internal Method

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
3.00 mm	HB		UL 94

Process Conditions
injection	Nominal value	Unit	Test method
Drying temperature	80	°C
Barrel rear temperature	220 to 275	°C
Barrel middle temperature	220 to 275	°C
Barrel front temperature	220 to 275	°C
Nozzle temperature	220 to 275	°C
Mold temperature	60	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.